diff options
Diffstat (limited to 'arch/arm64/boot/dts/qcom/sc8280xp-lenovo-thinkpad-x13s.dts')
-rw-r--r-- | arch/arm64/boot/dts/qcom/sc8280xp-lenovo-thinkpad-x13s.dts | 730 |
1 files changed, 615 insertions, 115 deletions
diff --git a/arch/arm64/boot/dts/qcom/sc8280xp-lenovo-thinkpad-x13s.dts b/arch/arm64/boot/dts/qcom/sc8280xp-lenovo-thinkpad-x13s.dts index 568c6be1ceaa..98e71b933437 100644 --- a/arch/arm64/boot/dts/qcom/sc8280xp-lenovo-thinkpad-x13s.dts +++ b/arch/arm64/boot/dts/qcom/sc8280xp-lenovo-thinkpad-x13s.dts @@ -21,7 +21,38 @@ model = "Lenovo ThinkPad X13s"; compatible = "lenovo,thinkpad-x13s", "qcom,sc8280xp"; - backlight { + aliases { + i2c4 = &i2c4; + i2c21 = &i2c21; + }; + + wcd938x: audio-codec { + compatible = "qcom,wcd9380-codec"; + + pinctrl-names = "default"; + pinctrl-0 = <&wcd_default>; + + reset-gpios = <&tlmm 106 GPIO_ACTIVE_LOW>; + + vdd-buck-supply = <&vreg_s10b>; + vdd-rxtx-supply = <&vreg_s10b>; + vdd-io-supply = <&vreg_s10b>; + vdd-mic-bias-supply = <&vreg_bob>; + + qcom,micbias1-microvolt = <1800000>; + qcom,micbias2-microvolt = <1800000>; + qcom,micbias3-microvolt = <1800000>; + qcom,micbias4-microvolt = <1800000>; + qcom,mbhc-buttons-vthreshold-microvolt = <75000 150000 237000 500000 500000 500000 500000 500000>; + qcom,mbhc-headset-vthreshold-microvolt = <1700000>; + qcom,mbhc-headphone-vthreshold-microvolt = <50000>; + qcom,rx-device = <&wcd_rx>; + qcom,tx-device = <&wcd_tx>; + + #sound-dai-cells = <1>; + }; + + backlight: backlight { compatible = "pwm-backlight"; pwms = <&pmc8280c_lpg 3 1000000>; enable-gpios = <&pmc8280_1_gpios 8 GPIO_ACTIVE_HIGH>; @@ -31,65 +62,113 @@ pinctrl-0 = <&edp_bl_en>, <&edp_bl_pwm>; }; - thermal-zones { - skin-temp-thermal { - polling-delay-passive = <250>; - polling-delay = <0>; - thermal-sensors = <&pmk8280_adc_tm 5>; + gpio-keys { + compatible = "gpio-keys"; - trips { - skin_temp_alert0: trip-point0 { - temperature = <55000>; - hysteresis = <1000>; - type = "passive"; + pinctrl-names = "default"; + pinctrl-0 = <&hall_int_n_default>; + + switch-lid { + gpios = <&tlmm 107 GPIO_ACTIVE_LOW>; + linux,input-type = <EV_SW>; + linux,code = <SW_LID>; + wakeup-source; + wakeup-event-action = <EV_ACT_DEASSERTED>; + }; + }; + + pmic-glink { + compatible = "qcom,sc8280xp-pmic-glink", "qcom,pmic-glink"; + + #address-cells = <1>; + #size-cells = <0>; + + connector@0 { + compatible = "usb-c-connector"; + reg = <0>; + power-role = "dual"; + data-role = "dual"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + pmic_glink_con0_hs: endpoint { + remote-endpoint = <&usb_0_role_switch>; + }; }; - skin_temp_alert1: trip-point1 { - temperature = <58000>; - hysteresis = <1000>; - type = "passive"; + port@1 { + reg = <1>; + + pmic_glink_con0_ss: endpoint { + remote-endpoint = <&mdss0_dp0_out>; + }; }; - skin-temp-crit { - temperature = <73000>; - hysteresis = <1000>; - type = "critical"; + port@2 { + reg = <2>; + + pmic_glink_con0_sbu: endpoint { + remote-endpoint = <&usb0_sbu_mux>; + }; }; }; + }; - cooling-maps { - map0 { - trip = <&skin_temp_alert0>; - cooling-device = <&CPU4 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, - <&CPU5 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, - <&CPU6 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, - <&CPU7 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; + connector@1 { + compatible = "usb-c-connector"; + reg = <1>; + power-role = "dual"; + data-role = "dual"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + port@0 { + reg = <0>; + + pmic_glink_con1_hs: endpoint { + remote-endpoint = <&usb_1_role_switch>; + }; }; - map1 { - trip = <&skin_temp_alert1>; - cooling-device = <&CPU4 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, - <&CPU5 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, - <&CPU6 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, - <&CPU7 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; + port@1 { + reg = <1>; + + pmic_glink_con1_ss: endpoint { + remote-endpoint = <&mdss0_dp1_out>; + }; + }; + + port@2 { + reg = <2>; + + pmic_glink_con1_sbu: endpoint { + remote-endpoint = <&usb1_sbu_mux>; + }; }; }; }; }; - gpio-keys { - compatible = "gpio-keys"; + vreg_edp_3p3: regulator-edp-3p3 { + compatible = "regulator-fixed"; + + regulator-name = "VCC3LCD"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + + gpio = <&tlmm 25 GPIO_ACTIVE_HIGH>; + enable-active-high; pinctrl-names = "default"; - pinctrl-0 = <&hall_int_n_default>; + pinctrl-0 = <&edp_reg_en>; - switch-lid { - gpios = <&tlmm 107 GPIO_ACTIVE_LOW>; - linux,input-type = <EV_SW>; - linux,code = <SW_LID>; - wakeup-source; - wakeup-event-action = <EV_ACT_DEASSERTED>; - }; + regulator-boot-on; }; vreg_edp_bl: regulator-edp-bl { @@ -141,6 +220,16 @@ regulator-boot-on; }; + vreg_vph_pwr: regulator-vph-pwr { + compatible = "regulator-fixed"; + + regulator-name = "VPH_VCC3R9"; + regulator-min-microvolt = <3900000>; + regulator-max-microvolt = <3900000>; + + regulator-always-on; + }; + vreg_wlan: regulator-wlan { compatible = "regulator-fixed"; @@ -172,15 +261,117 @@ regulator-boot-on; }; + + reserved-memory { + linux,cma { + compatible = "shared-dma-pool"; + size = <0x0 0x8000000>; + reusable; + linux,cma-default; + }; + }; + + thermal-zones { + skin-temp-thermal { + polling-delay-passive = <250>; + polling-delay = <0>; + thermal-sensors = <&pmk8280_adc_tm 5>; + + trips { + skin_temp_alert0: trip-point0 { + temperature = <55000>; + hysteresis = <1000>; + type = "passive"; + }; + + skin_temp_alert1: trip-point1 { + temperature = <58000>; + hysteresis = <1000>; + type = "passive"; + }; + + skin-temp-crit { + temperature = <73000>; + hysteresis = <1000>; + type = "critical"; + }; + }; + + cooling-maps { + map0 { + trip = <&skin_temp_alert0>; + cooling-device = <&CPU4 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU5 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU6 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU7 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; + }; + + map1 { + trip = <&skin_temp_alert1>; + cooling-device = <&CPU4 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU5 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU6 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU7 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; + }; + }; + }; + }; + + usb0-sbu-mux { + compatible = "pericom,pi3usb102", "gpio-sbu-mux"; + + enable-gpios = <&tlmm 101 GPIO_ACTIVE_LOW>; + select-gpios = <&tlmm 164 GPIO_ACTIVE_HIGH>; + + pinctrl-names = "default"; + pinctrl-0 = <&usb0_sbu_default>; + + mode-switch; + orientation-switch; + svid = /bits/ 16 <0xff01>; + + port { + usb0_sbu_mux: endpoint { + remote-endpoint = <&pmic_glink_con0_sbu>; + }; + }; + }; + + usb1-sbu-mux { + compatible = "pericom,pi3usb102", "gpio-sbu-mux"; + + enable-gpios = <&tlmm 48 GPIO_ACTIVE_LOW>; + select-gpios = <&tlmm 47 GPIO_ACTIVE_HIGH>; + + pinctrl-names = "default"; + pinctrl-0 = <&usb1_sbu_default>; + + mode-switch; + orientation-switch; + svid = /bits/ 16 <0xff01>; + + port { + usb1_sbu_mux: endpoint { + remote-endpoint = <&pmic_glink_con1_sbu>; + }; + }; + }; }; &apps_rsc { - pmc8280-1-rpmh-regulators { + regulators-0 { compatible = "qcom,pm8350-rpmh-regulators"; qcom,pmic-id = "b"; vdd-l3-l5-supply = <&vreg_s11b>; + vreg_s10b: smps10 { + regulator-name = "vreg_s10b"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + vreg_s11b: smps11 { regulator-name = "vreg_s11b"; regulator-min-microvolt = <1272000>; @@ -188,6 +379,13 @@ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; }; + vreg_s12b: smps12 { + regulator-name = "vreg_s12b"; + regulator-min-microvolt = <984000>; + regulator-max-microvolt = <984000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + vreg_l3b: ldo3 { regulator-name = "vreg_l3b"; regulator-min-microvolt = <1200000>; @@ -209,13 +407,13 @@ regulator-max-microvolt = <880000>; regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; regulator-boot-on; - regulator-always-on; /* FIXME: VDD_A_EDP_0_0P9 */ }; }; - pmc8280c-rpmh-regulators { + regulators-1 { compatible = "qcom,pm8350c-rpmh-regulators"; qcom,pmic-id = "c"; + vdd-bob-supply = <&vreg_vph_pwr>; vreg_l1c: ldo1 { regulator-name = "vreg_l1c"; @@ -237,9 +435,16 @@ regulator-max-microvolt = <3072000>; regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; }; + + vreg_bob: bob { + regulator-name = "vreg_bob"; + regulator-min-microvolt = <3008000>; + regulator-max-microvolt = <3960000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_AUTO>; + }; }; - pmc8280-2-rpmh-regulators { + regulators-2 { compatible = "qcom,pm8350-rpmh-regulators"; qcom,pmic-id = "d"; @@ -282,6 +487,148 @@ }; }; +&dispcc0 { + status = "okay"; +}; + +&mdss0 { + status = "okay"; +}; + +&mdss0_dp0 { + status = "okay"; +}; + +&mdss0_dp0_out { + data-lanes = <0 1>; + remote-endpoint = <&pmic_glink_con0_ss>; +}; + +&mdss0_dp1 { + status = "okay"; +}; + +&mdss0_dp1_out { + data-lanes = <0 1>; + remote-endpoint = <&pmic_glink_con1_ss>; +}; + +&mdss0_dp3 { + compatible = "qcom,sc8280xp-edp"; + + data-lanes = <0 1 2 3>; + + status = "okay"; + + aux-bus { + panel { + compatible = "edp-panel"; + + backlight = <&backlight>; + power-supply = <&vreg_edp_3p3>; + + ports { + port { + edp_panel_in: endpoint { + remote-endpoint = <&mdss0_dp3_out>; + }; + }; + }; + }; + }; + + ports { + port@1 { + reg = <1>; + mdss0_dp3_out: endpoint { + remote-endpoint = <&edp_panel_in>; + }; + }; + }; +}; + +&mdss0_dp3_phy { + vdda-phy-supply = <&vreg_l6b>; + vdda-pll-supply = <&vreg_l3b>; + + status = "okay"; +}; + +&i2c4 { + clock-frequency = <400000>; + + pinctrl-names = "default"; + pinctrl-0 = <&i2c4_default>; + + status = "okay"; + + /* FIXME: verify */ + touchscreen@10 { + compatible = "hid-over-i2c"; + reg = <0x10>; + + hid-descr-addr = <0x1>; + interrupts-extended = <&tlmm 175 IRQ_TYPE_LEVEL_LOW>; + vdd-supply = <&vreg_misc_3p3>; + + pinctrl-names = "default"; + pinctrl-0 = <&ts0_default>; + }; +}; + +&i2c21 { + clock-frequency = <400000>; + + pinctrl-names = "default"; + pinctrl-0 = <&i2c21_default>; + + status = "okay"; + + touchpad@15 { + compatible = "hid-over-i2c"; + reg = <0x15>; + + hid-descr-addr = <0x1>; + interrupts-extended = <&tlmm 182 IRQ_TYPE_LEVEL_LOW>; + vdd-supply = <&vreg_misc_3p3>; + + pinctrl-names = "default"; + pinctrl-0 = <&tpad_default>; + + wakeup-source; + + status = "disabled"; + }; + + touchpad@2c { + compatible = "hid-over-i2c"; + reg = <0x2c>; + + hid-descr-addr = <0x20>; + interrupts-extended = <&tlmm 182 IRQ_TYPE_LEVEL_LOW>; + vdd-supply = <&vreg_misc_3p3>; + + pinctrl-names = "default"; + pinctrl-0 = <&tpad_default>; + + wakeup-source; + }; + + keyboard@68 { + compatible = "hid-over-i2c"; + reg = <0x68>; + + hid-descr-addr = <0x1>; + interrupts-extended = <&tlmm 104 IRQ_TYPE_LEVEL_LOW>; + vdd-supply = <&vreg_misc_3p3>; + + pinctrl-names = "default"; + pinctrl-0 = <&kybd_default>; + + wakeup-source; + }; +}; + &pcie2a { perst-gpios = <&tlmm 143 GPIO_ACTIVE_LOW>; wake-gpios = <&tlmm 145 GPIO_ACTIVE_LOW>; @@ -501,98 +848,157 @@ status = "okay"; }; -&qup0_i2c4 { - clock-frequency = <400000>; - - pinctrl-names = "default"; - pinctrl-0 = <&qup0_i2c4_default>; - +&qup1 { status = "okay"; +}; - /* FIXME: verify */ - touchscreen@10 { - compatible = "hid-over-i2c"; - reg = <0x10>; +&qup2 { + status = "okay"; +}; - hid-descr-addr = <0x1>; - interrupts-extended = <&tlmm 175 IRQ_TYPE_LEVEL_LOW>; - vdd-supply = <&vreg_misc_3p3>; +&remoteproc_adsp { + firmware-name = "qcom/sc8280xp/LENOVO/21BX/qcadsp8280.mbn"; - pinctrl-names = "default"; - pinctrl-0 = <&ts0_default>; - }; + status = "okay"; }; -&qup1 { +&remoteproc_nsp0 { + firmware-name = "qcom/sc8280xp/LENOVO/21BX/qccdsp8280.mbn"; + status = "okay"; }; -&qup2 { +&rxmacro { status = "okay"; }; -&qup2_i2c5 { - clock-frequency = <400000>; +&sound { + compatible = "qcom,sc8280xp-sndcard"; + model = "SC8280XP-LENOVO-X13S"; + audio-routing = + "SpkrLeft IN", "WSA_SPK1 OUT", + "SpkrRight IN", "WSA_SPK2 OUT", + "IN1_HPHL", "HPHL_OUT", + "IN2_HPHR", "HPHR_OUT", + "AMIC2", "MIC BIAS2", + "VA DMIC0", "MIC BIAS1", + "VA DMIC1", "MIC BIAS1", + "VA DMIC2", "MIC BIAS3", + "TX DMIC0", "MIC BIAS1", + "TX DMIC1", "MIC BIAS2", + "TX DMIC2", "MIC BIAS3", + "TX SWR_ADC1", "ADC2_OUTPUT"; + + wcd-playback-dai-link { + link-name = "WCD Playback"; + cpu { + sound-dai = <&q6apmbedai RX_CODEC_DMA_RX_0>; + }; - pinctrl-names = "default"; - pinctrl-0 = <&qup2_i2c5_default>; + codec { + sound-dai = <&wcd938x 0>, <&swr1 0>, <&rxmacro 0>; + }; - status = "okay"; + platform { + sound-dai = <&q6apm>; + }; + }; - touchpad@15 { - compatible = "hid-over-i2c"; - reg = <0x15>; + wcd-capture-dai-link { + link-name = "WCD Capture"; + cpu { + sound-dai = <&q6apmbedai TX_CODEC_DMA_TX_3>; + }; - hid-descr-addr = <0x1>; - interrupts-extended = <&tlmm 182 IRQ_TYPE_LEVEL_LOW>; - vdd-supply = <&vreg_misc_3p3>; + codec { + sound-dai = <&wcd938x 1>, <&swr2 0>, <&txmacro 0>; + }; - pinctrl-names = "default"; - pinctrl-0 = <&tpad_default>; + platform { + sound-dai = <&q6apm>; + }; + }; - wakeup-source; + wsa-dai-link { + link-name = "WSA Playback"; + cpu { + sound-dai = <&q6apmbedai WSA_CODEC_DMA_RX_0>; + }; - status = "disabled"; - }; + codec { + sound-dai = <&left_spkr>, <&right_spkr>, <&swr0 0>, <&wsamacro 0>; + }; - touchpad@2c { - compatible = "hid-over-i2c"; - reg = <0x2c>; + platform { + sound-dai = <&q6apm>; + }; + }; - hid-descr-addr = <0x20>; - interrupts-extended = <&tlmm 182 IRQ_TYPE_LEVEL_LOW>; - vdd-supply = <&vreg_misc_3p3>; + va-dai-link { + link-name = "VA Capture"; + cpu { + sound-dai = <&q6apmbedai TX_CODEC_DMA_TX_3>; + }; - pinctrl-names = "default"; - pinctrl-0 = <&tpad_default>; + platform { + sound-dai = <&q6apm>; + }; - wakeup-source; + codec { + sound-dai = <&vamacro 0>; + }; }; +}; - keyboard@68 { - compatible = "hid-over-i2c"; - reg = <0x68>; - - hid-descr-addr = <0x1>; - interrupts-extended = <&tlmm 104 IRQ_TYPE_LEVEL_LOW>; - vdd-supply = <&vreg_misc_3p3>; +&swr0 { + status = "okay"; + left_spkr: wsa8830-left@0,1 { + compatible = "sdw10217020200"; + reg = <0 1>; pinctrl-names = "default"; - pinctrl-0 = <&kybd_default>; + pinctrl-0 = <&spkr_1_sd_n_default>; + powerdown-gpios = <&tlmm 178 GPIO_ACTIVE_LOW>; + #thermal-sensor-cells = <0>; + sound-name-prefix = "SpkrLeft"; + #sound-dai-cells = <0>; + vdd-supply = <&vreg_s10b>; + }; - wakeup-source; + right_spkr: wsa8830-right@0,2 { + compatible = "sdw10217020200"; + reg = <0 2>; + pinctrl-names = "default"; + pinctrl-0 = <&spkr_2_sd_n_default>; + powerdown-gpios = <&tlmm 179 GPIO_ACTIVE_LOW>; + #thermal-sensor-cells = <0>; + sound-name-prefix = "SpkrRight"; + #sound-dai-cells = <0>; + vdd-supply = <&vreg_s10b>; }; }; -&remoteproc_adsp { - firmware-name = "qcom/sc8280xp/LENOVO/21BX/qcadsp8280.mbn"; - +&swr1 { status = "okay"; + + wcd_rx: wcd9380-rx@0,4 { + compatible = "sdw20217010d00"; + reg = <0 4>; + qcom,rx-port-mapping = <1 2 3 4 5>; + }; }; -&remoteproc_nsp0 { - firmware-name = "qcom/sc8280xp/LENOVO/21BX/qccdsp8280.mbn"; +&swr2 { + status = "okay"; + + wcd_tx: wcd9380-tx@0,3 { + compatible = "sdw20217010d00"; + reg = <0 3>; + qcom,tx-port-mapping = <1 1 2 3>; + }; +}; +&txmacro { status = "okay"; }; @@ -601,7 +1007,6 @@ }; &usb_0_dwc3 { - /* TODO: Define USB-C connector properly */ dr_mode = "host"; }; @@ -620,12 +1025,15 @@ status = "okay"; }; +&usb_0_role_switch { + remote-endpoint = <&pmic_glink_con0_hs>; +}; + &usb_1 { status = "okay"; }; &usb_1_dwc3 { - /* TODO: Define USB-C connector properly */ dr_mode = "host"; }; @@ -644,12 +1052,35 @@ status = "okay"; }; +&usb_1_role_switch { + remote-endpoint = <&pmic_glink_con1_hs>; +}; + +&vamacro { + pinctrl-0 = <&dmic01_default>, <&dmic02_default>; + pinctrl-names = "default"; + + vdd-micb-supply = <&vreg_s10b>; + + qcom,dmic-sample-rate = <600000>; + + status = "okay"; +}; + +&wsamacro { + status = "okay"; +}; + &xo_board_clk { clock-frequency = <38400000>; }; /* PINCTRL */ +&lpass_tlmm { + status = "okay"; +}; + &pmc8280_1_gpios { edp_bl_en: edp-bl-en-state { pins = "gpio8"; @@ -691,6 +1122,13 @@ &tlmm { gpio-reserved-ranges = <70 2>, <74 6>, <83 4>, <125 2>, <128 2>, <154 7>; + edp_reg_en: edp-reg-en-state { + pins = "gpio25"; + function = "gpio"; + drive-strength = <16>; + bias-disable; + }; + hall_int_n_default: hall-int-n-state { pins = "gpio107"; function = "gpio"; @@ -698,6 +1136,20 @@ bias-disable; }; + i2c4_default: i2c4-default-state { + pins = "gpio171", "gpio172"; + function = "qup4"; + drive-strength = <16>; + bias-disable; + }; + + i2c21_default: i2c21-default-state { + pins = "gpio81", "gpio82"; + function = "qup21"; + drive-strength = <16>; + bias-disable; + }; + kybd_default: kybd-default-state { disable-pins { pins = "gpio102"; @@ -794,18 +1246,24 @@ }; }; - qup0_i2c4_default: qup0-i2c4-default-state { - pins = "gpio171", "gpio172"; - function = "qup4"; - bias-disable; - drive-strength = <16>; + spkr_1_sd_n_default: spkr-1-sd-n-default-state { + perst-n-pins { + pins = "gpio178"; + function = "gpio"; + drive-strength = <16>; + bias-disable; + output-high; + }; }; - qup2_i2c5_default: qup2-i2c5-default-state { - pins = "gpio81", "gpio82"; - function = "qup21"; - bias-disable; - drive-strength = <16>; + spkr_2_sd_n_default: spkr-2-sd-n-default-state { + perst-n-pins { + pins = "gpio179"; + function = "gpio"; + drive-strength = <16>; + bias-disable; + output-high; + }; }; tpad_default: tpad-default-state { @@ -830,4 +1288,46 @@ drive-strength = <16>; }; }; + + usb0_sbu_default: usb0-sbu-state { + oe-n-pins { + pins = "gpio101"; + function = "gpio"; + bias-disable; + drive-strengh = <16>; + output-high; + }; + + sel-pins { + pins = "gpio164"; + function = "gpio"; + bias-disable; + drive-strength = <16>; + }; + }; + + usb1_sbu_default: usb1-sbu-state { + oe-n-pins { + pins = "gpio48"; + function = "gpio"; + bias-disable; + drive-strengh = <16>; + output-high; + }; + + sel-pins { + pins = "gpio47"; + function = "gpio"; + bias-disable; + drive-strength = <16>; + }; + }; + + wcd_default: wcd-default-state { + reset-pins { + pins = "gpio106"; + function = "gpio"; + bias-disable; + }; + }; }; |