Merge airlied/drm-next into drm-misc-nextdrm-misc-next-2018-03-21

Refresh -misc-next

Signed-off-by: Sean Paul <seanpaul@chromium.org>

1 files changed, 15 insertions, 13 deletions

diff --git a/drivers/gpu/drm/i915/intel_dvo.c b/drivers/gpu/drm/i915/intel_dvo.c
index 59c066ca14e5..eb0c559b2715 100644
--- a/drivers/gpu/drm/i915/intel_dvo.c
+++ b/drivers/gpu/drm/i915/intel_dvo.c
@@ -245,7 +245,8 @@ static bool intel_dvo_compute_config(struct intel_encoder *encoder,
 		intel_dvo->attached_connector->panel.fixed_mode;
 	struct drm_display_mode *adjusted_mode = &pipe_config->base.adjusted_mode;
 
-	/* If we have timings from the BIOS for the panel, put them in
+	/*
+	 * If we have timings from the BIOS for the panel, put them in
 	 * to the adjusted mode.  The CRTC will be set up for this mode,
 	 * with the panel scaling set up to source from the H/VDisplay
 	 * of the original mode.
@@ -293,11 +294,6 @@ static void intel_dvo_pre_enable(struct intel_encoder *encoder,
 	I915_WRITE(dvo_reg, dvo_val);
 }
 
-/**
- * Detect the output connection on our DVO device.
- *
- * Unimplemented.
- */
 static enum drm_connector_status
 intel_dvo_detect(struct drm_connector *connector, bool force)
 {
@@ -313,7 +309,8 @@ static int intel_dvo_get_modes(struct drm_connector *connector)
 	const struct drm_display_mode *fixed_mode =
 		to_intel_connector(connector)->panel.fixed_mode;
 
-	/* We should probably have an i2c driver get_modes function for those
+	/*
+	 * We should probably have an i2c driver get_modes function for those
 	 * devices which will have a fixed set of modes determined by the chip
 	 * (TV-out, for example), but for now with just TMDS and LVDS,
 	 * that's not the case.
@@ -371,7 +368,7 @@ static const struct drm_encoder_funcs intel_dvo_enc_funcs = {
 	.destroy = intel_dvo_enc_destroy,
 };
 
-/**
+/*
  * Attempts to get a fixed panel timing for LVDS (currently only the i830).
  *
  * Other chips with DVO LVDS will need to extend this to deal with the LVDS
@@ -443,7 +440,8 @@ void intel_dvo_init(struct drm_i915_private *dev_priv)
 		uint32_t dpll[I915_MAX_PIPES];
 		enum port port;
 
-		/* Allow the I2C driver info to specify the GPIO to be used in
+		/*
+		 * Allow the I2C driver info to specify the GPIO to be used in
 		 * special cases, but otherwise default to what's defined
 		 * in the spec.
 		 */
@@ -454,7 +452,8 @@ void intel_dvo_init(struct drm_i915_private *dev_priv)
 		else
 			gpio = GMBUS_PIN_DPB;
 
-		/* Set up the I2C bus necessary for the chip we're probing.
+		/*
+		 * Set up the I2C bus necessary for the chip we're probing.
 		 * It appears that everything is on GPIOE except for panels
 		 * on i830 laptops, which are on GPIOB (DVOA).
 		 */
@@ -462,12 +461,14 @@ void intel_dvo_init(struct drm_i915_private *dev_priv)
 
 		intel_dvo->dev = *dvo;
 
-		/* GMBUS NAK handling seems to be unstable, hence let the
+		/*
+		 * GMBUS NAK handling seems to be unstable, hence let the
 		 * transmitter detection run in bit banging mode for now.
 		 */
 		intel_gmbus_force_bit(i2c, true);
 
-		/* ns2501 requires the DVO 2x clock before it will
+		/*
+		 * ns2501 requires the DVO 2x clock before it will
 		 * respond to i2c accesses, so make sure we have
 		 * have the clock enabled before we attempt to
 		 * initialize the device.
@@ -525,7 +526,8 @@ void intel_dvo_init(struct drm_i915_private *dev_priv)
 
 		intel_connector_attach_encoder(intel_connector, intel_encoder);
 		if (dvo->type == INTEL_DVO_CHIP_LVDS) {
-			/* For our LVDS chipsets, we should hopefully be able
+			/*
+			 * For our LVDS chipsets, we should hopefully be able
 			 * to dig the fixed panel mode out of the BIOS data.
 			 * However, it's in a different format from the BIOS
 			 * data on chipsets with integrated LVDS (stored in AIM