/**
@page touchpad_pressure Touchpad pressure-based touch detection

libinput uses the touchpad pressure values to detect wether a finger has
been placed on the touchpad. This is @ref kernel_pressure_information and
combines with a libinput-specific hardware database to adjust the thresholds
on a per-device basis. libinput uses pressure thresholds primarily to filter
out accidental light touches but pressure information is also used for
some @ref palm_detection.

Pressure thresholds are **not** directly configurable by the user, rather it
is planned that libinput provides custom pressure thresholds for each device
where necessary. See @ref touchpad_pressure_hwdb for instructions for your
local device.

@section kernel_pressure_information Information provided by the kernel

The kernel sends multiple values to inform userspace about a finger touching
the touchpad. The most basic is the ```EV_KEY/BTN_TOUCH``` boolean event
that simply announces physical contact with the touchpad. The decision when
this event is sent is usually made by the kernel driver and may depend on
device-specific thresholds. These thresholds are transparent to userspace
and cannot be modified.

Many contemporary touchpad devices provide an absolute pressure axis in
addition to ```BTN_TOUCH```. This pressure generally increases as the pressure
increases, however few touchpads are capable of detection pressure. The
pressure value is usually related to the covered area - as the pressure
increases a finger flattens and thus covers a larger area. The range
provided by the kernel is not mapped to a specific physical range and
often requires adjustment. Pressure is sent by the ```ABS_PRESSURE``` axis
for single-touch touchpads or ```ABS_MT_PRESSURE``` on multi-touch capable
touchpads.

Some devices provide additional touch size information through
the ```ABS_MT_TOUCH_MAJOR/ABS_MT_TOUCH_MINOR``` axes and/or
the ```ABS_MT_WIDTH_MAJOR/ABS_MT_WIDTH_MINOR``` axes. While the kernel
documentation specifies how these axes are supposed to be mapped, few
devices forward
reliable information.

@section touchpad_pressure_hwdb Debugging touchpad pressure ranges

This section describes how to determine the touchpad pressure ranges
required for a touchpad device and how to add the required hwdb entry
locally. Note that the hwdb entry is **not public API** and **may change at
any time**. Users are advised to @ref reporting_bugs "report a bug" with the
updated pressure ranges when testing has completed.

Use the ```libinput measure touchpad-pressure``` tool provided by libinput.
This tool will search for your touchpad device and print some pressure
statistics, including whether a touch is/was considered logically down.
Example output of the tool is below:

<pre>
$ sudo libinput measure touchpad-pressure
Ready for recording data.
Pressure range used: 8:10
Palm pressure range used: 65535
Place a single finger on the touchpad to measure pressure values.
Ctrl+C to exit
&nbsp;
Sequence 1190 pressure: min:  39 max:  48 avg:  43 median:  44 tags: down
Sequence 1191 pressure: min:  49 max:  65 avg:  62 median:  64 tags: down
Sequence 1192 pressure: min:  40 max:  78 avg:  64 median:  66 tags: down
Sequence 1193 pressure: min:  36 max:  83 avg:  70 median:  73 tags: down
Sequence 1194 pressure: min:  43 max:  76 avg:  72 median:  74 tags: down
Touchpad pressure:  47 min:  47 max:  86 tags: down
</pre>

The example output shows five completed touch sequences and one ongoing one.
For each, the respective minimum and maximum pressure values are printed as
well as some statistics. The ```tags``` show that sequence was considered
logically down at some point. This is an interactive tool and its output may
change frequently. Refer to the <i>libinput-measure-touchpad-pressure(1)</i> man
page for more details.

By default, this tool uses the udev hwdb entries for the pressure range. To
narrow down on the best values for your device, specify the 'logically down'
and 'logically up' pressure thresholds with the  ```--touch-thresholds``
argument:
<pre>
$ sudo libinput measure touchpad-pressure --touch-thresholds=10:8
</pre>

Interact with the touchpad and check if the output of this tool matches your
expectations.

Once the thresholds are decided on (e.g. 10 and 8), they can be enabled with
the following hwdb file:

<pre>
$> cat /etc/udev/hwdb.d/99-touchpad-pressure.hwdb
libinput:name:*SynPS/2 Synaptics TouchPad:dmi:*svnHewlett-Packard:*pnHPCompaq6910p*
 LIBINPUT_ATTR_PRESSURE_RANGE=10:8
</pre>

The first line is the match line and should be adjusted for the device name
(see evemu-record's output) and for the local system, based on the
information in ```/sys/class/dmi/id/modalias```. The modalias should be
shortened to the specific system's information, usually system vendor (svn)
and product name (pn).

Once in place, you need to run the following to commands, adjusted for your
device's event node (see @ref faq_hwdb_changes):
<pre>
    sudo udevadm hwdb --update
    sudo udevadm test /sys/class/input/eventX
</pre>

If the pressure range property shows up correctly, restart X or the
Wayland compositor and libinput should now use the correct pressure
thresholds. The @ref tools can be used to verify the correct
functionality first without the need for a restart.

Once the pressure ranges are deemed correct,
@ref reporting_bugs "report a bug" to get the pressure ranges into the
repository.

*/