| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
If width or height are in the [2049, 3072] range, allow to
use just three tiles in this dimension, instead of four.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Steve Longerbeam <slongerbeam@gmail.com>
Tested-by: Steve Longerbeam <slongerbeam@gmail.com>
|
|
Double-buffering only works if tile sizes are the same and the resizing
coefficient does not change between tiles, even for non-planar formats.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Steve Longerbeam <slongerbeam@gmail.com>
Tested-by: Steve Longerbeam <slongerbeam@gmail.com>
|
|
Visualize the scaling and rotation pipeline with some ASCII art
diagrams. Remove the FIXME comment about missing seam prevention.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Steve Longerbeam <slongerbeam@gmail.com>
|
|
For planar formats, bytesperline does not depend on BPP. It must always
be larger than width and aligned to tile width alignment restrictions.
The input bytesperline to ipu_image_convert_adjust() may be
uninitialized, so don't rely on input bytesperline as the
minimum value for clamp_align(). Use 2 << w_align as the minimum
instead.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
[slongerbeam@gmail.com: clamp input bytesperline]
Signed-off-by: Steve Longerbeam <slongerbeam@gmail.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
For the planar but U/V-packed formats NV12 and NV16, 8 pixel width
alignment is good enough to fulfill the 8 byte stride requirement.
If we allow the input 8-pixel DMA bursts to overshoot the end of the
line, the only input alignment restrictions are dictated by the pixel
format and 8-byte aligned line start address.
Since different tile sizes are allowed, the output tile with / height
alignment doesn't need to be multiplied by number of columns / rows.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
[slongerbeam@gmail.com: Bring in the fixes to format width and
height alignment restrictions from imx-media-mem2mem.c.]
Signed-off-by: Steve Longerbeam <slongerbeam@gmail.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
Since tile dimensions now vary between tiles, add debug output for each
tile's position and dimensions.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Steve Longerbeam <slongerbeam@gmail.com>
Tested-by: Steve Longerbeam <slongerbeam@gmail.com>
|
|
Select seam positions that minimize distortions during seam hiding while
satifying input and output IDMAC, rotator, and image format constraints.
This code looks for aligned output seam positions that minimize the
difference between the fractional corresponding ideal input positions
and the input positions rounded to alignment requirements.
Since now tiles can be sized differently, alignment restrictions of the
complete image can be relaxed in the next step.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Steve Longerbeam <slongerbeam@gmail.com>
Tested-by: Steve Longerbeam <slongerbeam@gmail.com>
|
|
Move tile_width_align and tile_height_align up so they
can be used by the tile edge position calculation code.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Steve Longerbeam <slongerbeam@gmail.com>
Tested-by: Steve Longerbeam <slongerbeam@gmail.com>
|
|
fill_image
This will allow to calculate seam positions after initializing the
ipu_image base structure but before calculating tile dimensions.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Steve Longerbeam <slongerbeam@gmail.com>
Tested-by: Steve Longerbeam <slongerbeam@gmail.com>
|
|
Store tile top/left position in pixels in the tile structure.
This will allow overlapping tiles with different sizes later.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Steve Longerbeam <slongerbeam@gmail.com>
Tested-by: Steve Longerbeam <slongerbeam@gmail.com>
|
|
For differently sized tiles or if the resizing coefficients change,
we have to stop, reconfigure, and restart the IC between tiles.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Steve Longerbeam <slongerbeam@gmail.com>
Tested-by: Steve Longerbeam <slongerbeam@gmail.com>
|
|
Slightly modifying resize coefficients per-tile allows to completely
hide the seams between tiles and to sample the correct input pixels at
the bottom and right edges of the image.
Tiling requires a bilinear interpolator reset at each tile start, which
causes the image to be slightly shifted if the starting pixel should not
have been sampled from an integer pixel position in the source image
according to the full image resizing ratio. To work around this
hardware limitation, calculate per-tile resizing coefficients that make
sure that the correct input pixels are sampled at the tile end.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Steve Longerbeam <slongerbeam@gmail.com>
Tested-by: Steve Longerbeam <slongerbeam@gmail.com>
|
|
Let convert_start start from a given tile index, allocate intermediate
tile with maximum tile size.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Steve Longerbeam <slongerbeam@gmail.com>
Tested-by: Steve Longerbeam <slongerbeam@gmail.com>
|
|
Catch calculated tile offsets that are not 8-byte aligned as required by the
IDMAC engine and return error in calc_tile_offsets().
Signed-off-by: Steve Longerbeam <slongerbeam@gmail.com>
Tested-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
The need_abort flag is not really needed anymore in
__ipu_image_convert_abort(), remove it.
No functional changes.
Signed-off-by: Steve Longerbeam <slongerbeam@gmail.com>
Tested-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
Allow reentrancy into ipu_image_convert_abort(), by moving re-init
of ctx->aborted completion under the spin lock, and only if there is
an active run, and complete all waiters do_bh(). Note:
ipu_image_convert_unprepare() is still _not_ reentrant, and can't
be made reentrant.
Signed-off-by: Steve Longerbeam <slongerbeam@gmail.com>
Tested-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
Only wait for the ctx->aborted completion if there is an active run
in progress, otherwise the wait will just timeout after 10 seconds.
If there is no active run in progress, the done queue just needs to
be emptied.
Signed-off-by: Steve Longerbeam <slongerbeam@gmail.com>
Tested-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
Prevent possible race by parallel threads between ipu_image_convert_run()
and ipu_image_convert_unprepare(). This involves setting ctx->aborting
to true unconditionally so that no new job runs can be queued during
unprepare, and holding the ctx->aborting flag until the context is freed.
Note that the "normal" ipu_image_convert_abort() case (e.g. not during
context unprepare) should clear the ctx->aborting flag after aborting
any active run and clearing the context's pending queue. This is because
it should be possible to continue to use the conversion context and queue
more runs after an abort.
Signed-off-by: Steve Longerbeam <slongerbeam@gmail.com>
Tested-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
For tiled scaling, we want to compute the scaling coefficients
externally in such a way that the interpolation overshoots tile
boundaries and samples up to the first pixel of the next tile.
Prepare to override the resizing coefficients from the image
conversion code.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Steve Longerbeam <slongerbeam@gmail.com>
Tested-by: Steve Longerbeam <slongerbeam@gmail.com>
|
|
Allow the caller of ipu_cpmem_set_image() to override the latters
calculation of the chroma plane offsets, by adding override U/V
plane offsets to 'struct ipu_image'.
Signed-off-by: Steve Longerbeam <slongerbeam@gmail.com>
Tested-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
Add a WARN_ON_ONCE() if either the Y/packed buffer, or the U/V offsets,
are not aligned on 8-byte boundaries. This will catch alignment
bugs in DRM, V4L2.
Signed-off-by: Steve Longerbeam <slongerbeam@gmail.com>
Tested-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
The CSI-2 bus may use either D-PHY or C-PHY. Make this visible in media
bus enum.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Tested-by: Steve Longerbeam <steve_longerbeam@mentor.com>
Tested-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
Pull drm updates from Dave Airlie:
"This is the main drm pull request for 4.19.
Rob has some new hardware support for new qualcomm hw that I'll send
along separately. This has the display part of it, the remaining pull
is for the acceleration engine.
This also contains a wound-wait/wait-die mutex rework, Peter has acked
it for merging via my tree.
Otherwise mostly the usual level of activity. Summary:
core:
- Wound-wait/wait-die mutex rework
- Add writeback connector type
- Add "content type" property for HDMI
- Move GEM bo to drm_framebuffer
- Initial gpu scheduler documentation
- GPU scheduler fixes for dying processes
- Console deferred fbcon takeover support
- Displayport support for CEC tunneling over AUX
panel:
- otm8009a panel driver fixes
- Innolux TV123WAM and G070Y2-L01 panel driver
- Ilitek ILI9881c panel driver
- Rocktech RK070ER9427 LCD
- EDT ETM0700G0EDH6 and EDT ETM0700G0BDH6
- DLC DLC0700YZG-1
- BOE HV070WSA-100
- newhaven, nhd-4.3-480272ef-atxl LCD
- DataImage SCF0700C48GGU18
- Sharp LQ035Q7DB03
- p079zca: Refactor to support multiple panels
tinydrm:
- ILI9341 display panel
New driver:
- vkms - virtual kms driver to testing.
i915:
- Icelake:
Display enablement
DSI support
IRQ support
Powerwell support
- GPU reset fixes and improvements
- Full ppgtt support refactoring
- PSR fixes and improvements
- Execlist improvments
- GuC related fixes
amdgpu:
- Initial amdgpu documentation
- JPEG engine support on VCN
- CIK uses powerplay by default
- Move to using core PCIE functionality for gens/lanes
- DC/Powerplay interface rework
- Stutter mode support for RV
- Vega12 Powerplay updates
- GFXOFF fixes
- GPUVM fault debugging
- Vega12 GFXOFF
- DC improvements
- DC i2c/aux changes
- UVD 7.2 fixes
- Powerplay fixes for Polaris12, CZ/ST
- command submission bo_list fixes
amdkfd:
- Raven support
- Power management fixes
udl:
- Cleanups and fixes
nouveau:
- misc fixes and cleanups.
msm:
- DPU1 support display controller in sdm845
- GPU coredump support.
vmwgfx:
- Atomic modesetting validation fixes
- Support for multisample surfaces
armada:
- Atomic modesetting support completed.
exynos:
- IPPv2 fixes
- Move g2d to component framework
- Suspend/resume support cleanups
- Driver cleanups
imx:
- CSI configuration improvements
- Driver cleanups
- Use atomic suspend/resume helpers
- ipu-v3 V4L2 XRGB32/XBGR32 support
pl111:
- Add Nomadik LCDC variant
v3d:
- GPU scheduler jobs management
sun4i:
- R40 display engine support
- TCON TOP driver
mediatek:
- MT2712 SoC support
rockchip:
- vop fixes
omapdrm:
- Workaround for DRA7 errata i932
- Fix mm_list locking
mali-dp:
- Writeback implementation
PM improvements
- Internal error reporting debugfs
tilcdc:
- Single fix for deferred probing
hdlcd:
- Teardown fixes
tda998x:
- Converted to a bridge driver.
etnaviv:
- Misc fixes"
* tag 'drm-next-2018-08-15' of git://anongit.freedesktop.org/drm/drm: (1506 commits)
drm/amdgpu/sriov: give 8s for recover vram under RUNTIME
drm/scheduler: fix param documentation
drm/i2c: tda998x: correct PLL divider calculation
drm/i2c: tda998x: get rid of private fill_modes function
drm/i2c: tda998x: move mode_valid() to bridge
drm/i2c: tda998x: register bridge outside of component helper
drm/i2c: tda998x: cleanup from previous changes
drm/i2c: tda998x: allocate tda998x_priv inside tda998x_create()
drm/i2c: tda998x: convert to bridge driver
drm/scheduler: fix timeout worker setup for out of order job completions
drm/amd/display: display connected to dp-1 does not light up
drm/amd/display: update clk for various HDMI color depths
drm/amd/display: program display clock on cache match
drm/amd/display: Add NULL check for enabling dp ss
drm/amd/display: add vbios table check for enabling dp ss
drm/amd/display: Don't share clk source between DP and HDMI
drm/amd/display: Fix DP HBR2 Eye Diagram Pattern on Carrizo
drm/amd/display: Use calculated disp_clk_khz value for dce110
drm/amd/display: Implement custom degamma lut on dcn
drm/amd/display: Destroy aux_engines only once
...
|
|
Merge changes in the PM core, system-wide PM infrastructure, generic
power domains (genpd) framework, ACPI PM infrastructure and cpuidle
for 4.19.
* pm-core:
driver core: Add flag to autoremove device link on supplier unbind
driver core: Rename flag AUTOREMOVE to AUTOREMOVE_CONSUMER
* pm-domains:
PM / Domains: Introduce dev_pm_domain_attach_by_name()
PM / Domains: Introduce option to attach a device by name to genpd
PM / Domains: dt: Add a power-domain-names property
* pm-sleep:
PM / reboot: Eliminate race between reboot and suspend
PM / hibernate: Mark expected switch fall-through
x86/power/hibernate_64: Remove VLA usage
PM / hibernate: cast PAGE_SIZE to int when comparing with error code
* acpi-pm:
ACPI / PM: save NVS memory for ASUS 1025C laptop
ACPI / PM: Default to s2idle in all machines supporting LP S0
* pm-cpuidle:
ARM: cpuidle: silence error on driver registration failure
|
|
git://git.pengutronix.de/git/pza/linux into drm-next
drm/imx: ipu-v3 plane offset and IPU id fixes
- Fix U/V plane offsets for odd vertical offsets. Due to wrong operator
order, the y offset was not rounded down properly for vertically
chroma subsampled planar formats.
- Fix IPU id number for boards that don't have an OF alias for their
single IPU in the device tree. This is necessary to support imx-media
on i.MX51 and i.MX53 SoCs.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Philipp Zabel <p.zabel@pengutronix.de>
Link: https://patchwork.freedesktop.org/patch/msgid/1533552680.4204.14.camel@pengutronix.de
|
|
This is better than storing -ENODEV in the id number. This fixes SoCs
with only one IPU that don't specify an IPU alias in the device tree.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
The U and V offset macros for planar 4:2:0 (U_OFFSET, V_OFFSET, and
UV_OFFSET), are not correct. The height component to the offset was
calculated as:
(pix->width * y / 4)
But this does not produce correct offsets for odd values of y (luma
line #). The luma line # must be decimated by two to produce the
correct U/V line #, so the correct formula is:
(pix->width * (y / 2) / 2)
Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
These should be used instead of the ill-defined deprecated RGB32 and
BGR32 V4L2 pixel formats.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
The IPU also supports interlaced buffers that start with the bottom field.
To achieve this, the the base address EBA has to be increased by a stride
length and the interlace offset ILO has to be set to the negative stride.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
|
|
The CSI_SENS_CONF_DATA_FMT_RGB565 configuration only works for MIPI
CSI-2 sources. On the parallel bus, we need to use bayer (generic) mode
instead. To handle this difference, we pass the mbus_type to
mbus_code_to_bus_cfg().
Signed-off-by: Jan Luebbe <jlu@pengutronix.de>
[p.zabel@pengutronix.de - renamed rc to ret for consistency]
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
mbus_code_to_bus_cfg() can fail on unknown mbus codes; pass back the
error to the caller.
Signed-off-by: Enrico Scholz <enrico.scholz@sigma-chemnitz.de>
Signed-off-by: Jan Luebbe <jlu@pengutronix.de>
[p.zabel@pengutronix.de - renamed rc to ret for consistency]
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
The 24bit RGB format configuration is currently missing, we add
it now.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
When the CSI is receiving from a bt.656 bus, include a check for
field type 'alternate' when determining whether to set CSI clock
mode to CCIR656_INTERLACED or CCIR656_PROGRESSIVE.
Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
When the definition of this struct was removed a forward declaration and an
unused struct member were still left around. Remove them because they serve
no purpose.
Fixes 44b460cfe554 ("drm: imx: remove struct imx_drm_crtc and imx_drm_crtc_helper_funcs")
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
Now that we want to add another flag to autoremove the device link
on supplier unbind, it's fair to rename the existing flag from
DL_FLAG_AUTOREMOVE to DL_FLAG_AUTOREMOVE_CONSUMER so that we can
add similar flag for supplier later.
And, while we are touching device.h, fix a doc build warning.
Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
gcc-8 reports that we access an array with a negative index
in an error case:
drivers/gpu/ipu-v3/ipu-prg.c: In function 'ipu_prg_channel_disable':
drivers/gpu/ipu-v3/ipu-prg.c:252:43: error: array subscript -22 is below array bounds of 'struct ipu_prg_channel[3]' [-Werror=array-bounds]
This moves the range check in front of the first time that
variable gets used.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
The 10/12-bit config used for bayer formats is used for grayscale as
well.
Signed-off-by: Jan Luebbe <jlu@pengutronix.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
Add the missing offset calculation for 16-bit grayscale images. Since
the IPU only supports capturing greyscale in raw passthrough mode, it
is the same as 16-bit bayer formats.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
Before returning, call of_node_put() for the device node returned by
of_parse_phandle().
Fixes: ea9c260514c1 ("gpu: ipu-v3: add driver for Prefetch Resolve Gasket")
Signed-off-by: Tobias Jordan <Tobias.Jordan@elektrobit.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
Before returning, call of_node_put() for the device node returned by
of_parse_phandle().
Fixes: d2a34232580a ("gpu: ipu-v3: add driver for Prefetch Resolve Engine")
Signed-off-by: Tobias Jordan <Tobias.Jordan@elektrobit.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
Add the missing offset calculation for grayscale images. Since the IPU
only supports capturing greyscale in raw passthrough mode, it is the
same as 8-bit bayer formats.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
Don't populate the const read-only arrays int_reg on the stack but instead
make them static. Makes the object code smaller by over 80 bytes:
Before:
text data bss dec hex filename
28024 8936 192 37152 9120 drivers/gpu/ipu-v3/ipu-common.o
After:
text data bss dec hex filename
27794 9080 192 37066 90ca drivers/gpu/ipu-v3/ipu-common.o
(gcc version 7.2.0 x86_64)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
Add missing include <linux/sizes.h> in ipu-cpmem and ipu-ic, select
BITREVERSE for ipu-cpmem and GENERIC_ALLOCATOR for ipu-pre, and allow
to build if COMPILE_TEST is enabled.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
Allow to pass through the modifier to the PRE unit and extend the
format check with the supported modifiers.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
This configures the TPR unit, using the DRM format modifier. For now only
the single buffer modifiers are supported, as split buffer needs more
configuration for the required cropping.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
[p.zabel@pengutronix.de: rebased after ERR009624 workaround]
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
Instead of open-coding the clk enable/disable in all of the callers
move this to the RPM suspend/resume functions.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
Pull more drm updates from Dave Airlie:
"Fixes/cleanups for rc1, non-desktop flags for VR
- remove the MSM dt-bindings file Rob managed to push in the previous
pull.
- add a property/edid quirk to denote HMD devices, I had these
hanging around for a few weeks and Keith had done some work on
them, they are fairly self contained and small, and only affect
people using HTC Vive VR headsets so far.
- amdgpu, tegra, tilcdc, fsl fixes
- some imx-drm cleanups I missed, these seemed pretty small, and no
reason to hold off.
I have one TTM regression fix (fixes bochs-vga in qemu) sitting
locally awaiting review I'll probably send that in a separate pull
request tomorrow"
* tag 'drm-for-v4.15-part2' of git://people.freedesktop.org/~airlied/linux: (33 commits)
dt-bindings: remove file that was added accidentally
drm/edid: quirk HTC vive headset as non-desktop. [v2]
drm/fb: add support for not enabling fbcon on non-desktop displays [v2]
drm: add connector info/property for non-desktop displays [v2]
drm/amdgpu: fix rmmod KCQ disable failed error
drm/amdgpu: fix kernel hang when starting VNC server
drm/amdgpu: don't skip attributes when powerplay is enabled
drm/amd/pp: fix typecast error in powerplay.
drm/tilcdc: Remove obsolete "ti,tilcdc,slave" dts binding support
drm/tegra: sor: Reimplement pad clock
Revert "drm/radeon: dont switch vt on suspend"
drm/amd/amdgpu: fix over-bound accessing in amdgpu_cs_wait_any_fence
drm/amd/powerplay: fix unfreeze level smc message for smu7
drm/amdgpu:fix memleak
drm/amdgpu:fix memleak in takedown
drm/amd/pp: fix dpm randomly failed on Vega10
drm/amdgpu: set f_mapping on exported DMA-bufs
drm/amdgpu: Properly allocate VM invalidate eng v2
drm/fsl-dcu: enable IRQ before drm_atomic_helper_resume()
drm/fsl-dcu: avoid disabling pixel clock twice on suspend
...
|
|
git://git.pengutronix.de/git/pza/linux into drm-next
drm/imx: various cleanups
- Switch to drm_*_get/put() helpers
- Use correct parallel-display connector enum: DPI instead of VGA
- Remove incorrect unit name from device tree binding documentation example
- Remove an unused variable
* tag 'imx-drm-next-2017-10-18' of git://git.pengutronix.de/git/pza/linux:
gpu: ipu-v3: ipu-dc: Remove unused 'di' variable
dt-bindings: fsl-imx-drm: Remove incorrect "@di0" usage
drm/imx: parallel-display: use correct connector enum
drm/imx: switch to drm_*_get(), drm_*_put() helpers
|
|
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The PRE has a bug where a software write to the CTRL register can block
the setting of the ENABLE bit by the hardware in auto repeat mode. When
this happens the PRE will fail to handle new jobs. To work around this
software must not write to CTRL register when the PRE store engine is
inside the unsafe window, where a hardware update to the ENABLE bit
may happen.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
[p.zabel@pengutronix.de: rebased before PRE tiled prefetch support]
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
