summaryrefslogtreecommitdiff
path: root/drivers/gpu/ipu-v3/ipu-csi.c
AgeCommit message (Collapse)AuthorFilesLines
2019-01-16media: gpu: ipu-csi: Swap fields according to input/output field typesSteve Longerbeam1-41/+85
The function ipu_csi_init_interface() was inverting the F-bit for NTSC case, in the CCIR_CODE_1/2 registers. The result being that for NTSC bottom-top field order, the CSI would swap fields and capture in top-bottom order. Instead, base field swap on the field order of the input to the CSI, and the field order of the requested output. If the input/output fields are sequential but different, swap fields, otherwise do not swap. This requires passing both the input and output mbus frame formats to ipu_csi_init_interface(). Move this code to a new private function ipu_csi_set_bt_interlaced_codes() that programs the CCIR_CODE_1/2 registers for interlaced BT.656 (and possibly interlaced BT.1120 in the future). When detecting input video standard from the input frame width/height, make sure to double height if input field type is alternate, since in that case input height only includes lines for one field. Signed-off-by: Steve Longerbeam <slongerbeam@gmail.com> Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
2018-10-04media: v4l: mediabus: Recognise CSI-2 D-PHY and C-PHYSakari Ailus1-3/+3
The CSI-2 bus may use either D-PHY or C-PHY. Make this visible in media bus enum. Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Tested-by: Steve Longerbeam <steve_longerbeam@mentor.com> Tested-by: Jacopo Mondi <jacopo+renesas@jmondi.org> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
2018-07-16gpu: ipu-v3: csi: support RGB565 on parallel busJan Luebbe1-4/+8
The CSI_SENS_CONF_DATA_FMT_RGB565 configuration only works for MIPI CSI-2 sources. On the parallel bus, we need to use bayer (generic) mode instead. To handle this difference, we pass the mbus_type to mbus_code_to_bus_cfg(). Signed-off-by: Jan Luebbe <jlu@pengutronix.de> [p.zabel@pengutronix.de - renamed rc to ret for consistency] Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
2018-07-16gpu: ipu-v3: csi: pass back mbus_code_to_bus_cfg error codesEnrico Scholz1-4/+16
mbus_code_to_bus_cfg() can fail on unknown mbus codes; pass back the error to the caller. Signed-off-by: Enrico Scholz <enrico.scholz@sigma-chemnitz.de> Signed-off-by: Jan Luebbe <jlu@pengutronix.de> [p.zabel@pengutronix.de - renamed rc to ret for consistency] Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
2018-07-16gpu: ipu-csi: add rgb/bgr888 24bit support to mbus_code_to_bus_cfgMichael Grzeschik1-0/+6
The 24bit RGB format configuration is currently missing, we add it now. Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de> Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
2018-07-16gpu: ipu-csi: Check for field type alternateSteve Longerbeam1-1/+2
When the CSI is receiving from a bt.656 bus, include a check for field type 'alternate' when determining whether to set CSI clock mode to CCIR656_INTERLACED or CCIR656_PROGRESSIVE. Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com> Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
2018-02-19gpu: ipu-csi: add 10/12-bit grayscale support to mbus_code_to_bus_cfgJan Luebbe1-0/+2
The 10/12-bit config used for bayer formats is used for grayscale as well. Signed-off-by: Jan Luebbe <jlu@pengutronix.de> Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
2017-02-17gpu: ipu-v3: export ipu_csi_set_downsizePhilipp Zabel1-0/+1
This function will be used by the media drivers and needs to be exported to allow them to be built as modules. Reported-by: Russell King <linux@armlinux.org.uk> Fixes: 867341b95891 ("gpu: ipu-v3: add ipu_csi_set_downsize") Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
2016-11-07gpu: ipu-v3: add ipu_csi_set_downsizePhilipp Zabel1-0/+16
Support downsizing to 1/2 width and/or height in the CSI. Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
2016-08-08gpu: ipu-v3: Fix CSI data format for 16-bit media bus formatsSteve Longerbeam1-5/+1
The CSI data format was being programmed incorrectly for the 1x16 media bus formats. The CSI data format for 16-bit must be bayer/generic (CSI_SENS_CONF_DATA_FMT_BAYER). Suggested-by: Carsten Resch <Carsten.Resch@de.bosch.com> Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com> Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
2016-08-08gpu: ipu-v3: set correct full sensor frame for PAL/NTSCSteve Longerbeam1-7/+13
Set the sensor full frame based on whether the passed in mbus_fmt is 720x480 (NTSC) or 720x576 (PAL). Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com> Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
2015-10-30gpu: ipu-v3: fix div_ratio typeAndrzej Hajda1-1/+1
The variable can be negative. The problem has been detected using proposed semantic patch scripts/coccinelle/tests/unsigned_lesser_than_zero.cocci [1]. [1]: http://permalink.gmane.org/gmane.linux.kernel/2038576 Signed-off-by: Andrzej Hajda <a.hajda@samsung.com> Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
2015-10-30gpu: ipu-v3: csi: add support for 8 bpp grayscale sensors.Philippe De Muyter1-0/+1
Enable the MEDIA_BUS_FMT_Y8_1X8 format. Signed-off-by: Philippe De Muyter <phdm@macqel.be> Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
2015-10-30gpu: ipu-v3: ipu-csi: bool test doesn't need a comparison to falseFabio Estevam1-1/+1
Bool initializations should use true and false. Bool tests don't need comparisons. Based on contributions from Joe Perches, Rusty Russell and Bruce W Allan. The semantic patch that makes this change is available in scripts/coccinelle/misc/boolinit.cocci. More information about semantic patching is available at http://coccinelle.lip6.fr/ Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
2014-11-14[media] gpu: ipu-v3: Make use of media_bus_format enumBoris BREZILLON1-33/+33
In order to have subsytem agnostic media bus format definitions we've moved media bus definition to include/uapi/linux/media-bus-format.h and prefixed enum values with MEDIA_BUS_FMT instead of V4L2_MBUS_FMT. Reference new definitions in the ipu-v3 driver. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Acked-by: Hans Verkuil <hans.verkuil@cisco.com> Acked-by: Philipp Zabel <p.zabel@pengutronix.de> Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
2014-09-02gpu: ipu-v3: Add Camera Sensor Interface unitSteve Longerbeam1-0/+741
Adds the Camera Sensor Interface (CSI) unit required for video capture. Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com> Removed the unused clk_get_rate in ipu_csi_init_interface and the ipu_csi_ccir_err_detection_enable/disable functions. Checkpatch cleanup. Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
generated by cgit v1.2.3 (git 2.39.1) at 2024-04-18 06:07:54 +0000