summaryrefslogtreecommitdiff
path: root/drivers/gpu/drm/amd/display/dc/dce
AgeCommit message (Collapse)AuthorFilesLines
2019-02-19drm/amd/display: Raise dispclk value for dce11Roman Li1-3/+8
[Why] The visual corruption due to low display clock value. Observed on Carrizo 4K@60Hz. [How] There was earlier patch for dce_update_clocks: Adding +15% workaround also to to dce11_update_clocks Signed-off-by: Roman Li <Roman.Li@amd.com> Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2019-02-01drm/amd/display: Fix fclk idle stateRoman Li1-1/+9
[Why] The earlier change 'Fix 6x4K displays' led to fclk value idling at higher DPM level. [How] Apply the fix only to respective multi-display configuration. Signed-off-by: Roman Li <Roman.Li@amd.com> Reviewed-by: Feifei Xu <Feifei.Xu@amd.com> Acked-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2018-12-18drm/amd/display: Raise dispclk value for PolarisRoman Li1-0/+7
[Why] The visual corruption due to low display clock value observed on some systems [How] There was earlier patch for dspclk: 'drm/amd/display: Raise dispclk value for dce_update_clocks' Adding +15% workaround also to to dce112_update_clocks Signed-off-by: Roman Li <Roman.Li@amd.com> Reviewed-by: Leo Li <Sunpeng.Li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2018-11-29drm/amd/display: Fix 6x4K displays light-up on Vega20Roman Li1-0/+2
[Why] More than 4x4K didn't lightup on Vega20 due to low dcfclk value. Powerplay expects valid min requirement for dcfclk from DC. [How] Update min_dcfclock_khz based on min_engine_clock value. Reviewed-by: Hersen Wu <hersenxs.wu@amd.com> Reviewed-by: Feifei Xu <Feifei.Xu@amd.com> Reviewed-by: Evan Quan <evan.quan@amd.com> Acked-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Roman Li <Roman.Li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2018-11-19drm/amd/display: Clean up dp_blank functionsDavid Francis1-13/+10
[Why] Unused variable "refresh" and incorrect comment formatting [How] Remove variable, reindent comments Signed-off-by: David Francis <David.Francis@amd.com> Reviewed-by: Tony Cheng <Tony.Cheng@amd.com> Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2018-11-19drm/amd/display: Check for dmcu initialization before calling dmcuDavid Francis1-4/+7
[Why] DMCU firmware is not required - the system is expected to run fine without it. Therefore, wherever dmcu functions could be called, dmcu initialization shoudl be checked [How] Use the helpful hook dmcu_funcs->is_dmcu_initialized Signed-off-by: David Francis <David.Francis@amd.com> Reviewed-by: Hersen Wu <hersenxs.wu@amd.com> Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2018-11-19drm/amd/display: expose dentist_get_divider_from_didNevenko Stupar2-1/+3
expose this functions for future use. Signed-off-by: Nevenko Stupar <Nevenko.Stupar@amd.com> Reviewed-by: Tony Cheng <Tony.Cheng@amd.com> Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2018-11-05drm/amd/display: Expose target backlight levelAnthony Koo1-0/+12
[Why] DM may want to understand any backlight optimizations applied, so DM needs a way to query from the HW both the real current backlight, which may be value during transition. And also target backlight, which may be after some backlight optimizations applied. [How] Add interface to query current and target backlight levels Target level may indicate backlight level after backlight optimization and reductions are applied. Signed-off-by: Anthony Koo <Anthony.Koo@amd.com> Reviewed-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2018-11-05drm/amd/display: Expand dc to use 16.16 bit backlightAnthony Koo1-54/+38
[Why] We want to increase precision for backlight setting. But DC interface takes 8 bit backlight level value only. [How] DMCU already takes 16 bit backlight level. Expand the DC interface to take 16.16 bit value. Max 32 bit backlight value (0xFFFF) will represent max backlight (100%) Signed-off-by: Anthony Koo <Anthony.Koo@amd.com> Reviewed-by: Tony Cheng <Tony.Cheng@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2018-11-05drm/amd/display: Add missing pipes registers for VGA enable/disableNevenko Stupar1-0/+2
Signed-off-by: Nevenko Stupar <Nevenko.Stupar@amd.com> Reviewed-by: Aric Cyr <Aric.Cyr@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2018-11-05drm/amd/display: add dccg blockDmytro Laktyushkin1-2/+5
This adds the hw block as well as hooks up dppclk dto programming Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com> Reviewed-by: Charlene Liu <Charlene.Liu@amd.com> Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2018-11-05drm/amd/display: rename dccg to clk_mgrDmytro Laktyushkin3-205/+205
In preparation for adding the actual dccg block since the current implementation of dccg is mor eof a clock manager than a hw block Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com> Reviewed-by: Charlene Liu <Charlene.Liu@amd.com> Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2018-11-05drm/amd/display: Add link encoder dp_ycbcr420_supported feature flagEric Bernstein1-1/+1
[Why] Need separate feature flag for DP 4:2:0 support, since existing flag is used for HDMI [How] Added dp_ycbcr420_supported to struct encoder_feature_support Signed-off-by: Eric Bernstein <eric.bernstein@amd.com> Reviewed-by: Tony Cheng <Tony.Cheng@amd.com> Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2018-11-05drm/amd/display: expose hwseq functions and add registersNevenko Stupar1-0/+50
Make these functions non static and define registers for future use is_lower_pipe_tree_visible(); is_upper_pipe_tree_visible(); is_pipe_tree_visible(); dcn10_program_pte_vm(); set_hdr_multiplier(); update_dchubp_dpp() find_top_pipe_for_stream() Signed-off-by: Nevenko Stupar <Nevenko.Stupar@amd.com> Reviewed-by: Charlene Liu <Charlene.Liu@amd.com> Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2018-11-05drm/amd/display: split dccg clock manager into asic foldersDmytro Laktyushkin3-285/+47
Currently dccg contains code related to every dcn revision in a single file. This change splits out the dcn parts of code into correct folders Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com> Reviewed-by: Charlene Liu <Charlene.Liu@amd.com> Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2018-11-05drm/amd/display: clean up base dccg structDmytro Laktyushkin2-20/+37
Move things not accessed outside dccg block into dce specific struct Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com> Reviewed-by: Tony Cheng <Tony.Cheng@amd.com> Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2018-11-05drm/amd/display: move pplib/smu notification to dccg blockDmytro Laktyushkin2-235/+430
This is done to clear up the clock programming sequence since the only time we need to notify pplib is after clock update. This also renames the clk block to dccg, at the moment this block contains both clock management and dccg functionality. Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com> Reviewed-by: Tony Cheng <Tony.Cheng@amd.com> Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2018-10-09drm/amd/display: Use proper enums in process_channel_replyNathan Chancellor1-1/+1
Clang warns when one enumerated type is implicitly converted to another. drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_aux.c:315:19: warning: implicit conversion from enumeration type 'enum aux_channel_operation_result' to different enumeration type 'enum aux_transaction_reply' [-Wenum-conversion] reply->status = AUX_CHANNEL_OPERATION_FAILED_HPD_DISCON; ~ ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ drivers/gpu/drm/amd/amdgpu/../display/dc/i2caux/dce110/aux_engine_dce110.c:349:19: warning: implicit conversion from enumeration type 'enum aux_channel_operation_result' to different enumeration type 'enum aux_transaction_reply' [-Wenum-conversion] reply->status = AUX_CHANNEL_OPERATION_FAILED_HPD_DISCON; ~ ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ The current enum is incorrect, it should be from aux_transaction_reply, so use AUX_TRANSACTION_REPLY_HPD_DISCON. Reported-by: Nick Desaulniers <ndesaulniers@google.com> Suggested-by: Nick Desaulniers <ndesaulniers@google.com> Signed-off-by: Nathan Chancellor <natechancellor@gmail.com> Reviewed-by: Nick Desaulniers <ndesaulniers@google.com> Reviewed-by: Harry Wentland <harry.wentland@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2018-10-09drm/amd/display: Raise dispclk value for dce_update_clocksNicholas Kazlauskas1-0/+5
[Why] The DISPCLK value was previously requested to be 15% higher for all ASICS that went through the dce110 bandwidth code path. As part of a refactoring of dce_clocks and dce110 set_bandwidth this was removed for power saving considerations. This changed caused corruption under certain display configurations. Originally thought to be Vega specific, it was also observed on Polaris. [How] The 15% is brought back but its placement differs from the original patch. This boost should only be enable while DFS bypass is inactive. This (like the Vega patch) is also a workaround that should be removed after the root cause is identified. Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com> Reviewed-by: Harry Wentland <Harry.Wentland@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2018-10-09drm/amd/display: clean up encoding checksEric Yang1-15/+1
[Why] All ASICS we support has YCbCr support, so the check is unnecessary, the currently logic in validate output also returns true all the time, so the unneccessary logic is removed Signed-off-by: Eric Yang <Eric.Yang2@amd.com> Reviewed-by: Tony Cheng <Tony.Cheng@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2018-10-09drm/amd/display: block DP YCbCr420 modesEric Yang1-0/+3
[why] Currently not supported, will black screen when set. [How] Fail validate timing helper for those modes. Signed-off-by: Eric Yang <Eric.Yang2@amd.com> Reviewed-by: Tony Cheng <Tony.Cheng@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2018-09-26drm/amd/display: Raise dispclk value for dce120 by 15%Nicholas Kazlauskas1-0/+3
[Why] The DISPCLK value was previously requested to be 15% higher for all ASICs that went through the dce110 bandwidth code path. As part of a refactoring of dce_clocks and the dce110 set bandwidth codepath this was removed for power saving considerations. That change caused display corruption under certain hardware configurations with Vega10. [How] The 15% DISPCLK increase is brought back but only on dce110 for now. This is should be a temporary workaround until the root cause is sorted out for why this occurs on Vega (or other ASICs, if reported). Tested-by: Nick Sarnie <sarnex@gentoo.org> Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com> Reviewed-by: Harry Wentland <Harry.Wentland@amd.com> Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2018-09-14drm/amd/display: stop using switch for different CS revisionsDmytro Laktyushkin2-164/+214
Clock sources currently have support for asic specific function pointers. But actual separation into functions was never performed, leaving us with giant functions that rely on switch. This change creates separate functions, removing switch use. Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com> Reviewed-by: Tony Cheng <Tony.Cheng@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2018-09-14drm/amd/display: Add Raven2 definitions in dcBhawanpreet Lakha1-0/+7
Add Raven2 definitions in the dc code Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com> Reviewed-by: Harry Wentland <harry.wentland@amd.com> Reviewed-by: Huang Rui <ray.huang@amd.com> Acked-by: Alex Deucher <alexander.deucher@amd.com Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2018-09-10drm/amd/display: remove unused clk_src codeDmytro Laktyushkin1-86/+1
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com> Reviewed-by: Charlene Liu <Charlene.Liu@amd.com> Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2018-08-27drm/amd/display: Flatten unnecessary i2c functionsDavid Francis1-77/+34
[Why] The dce_i2c_hw code contained four funtcions that were only called in one place and did not have a clearly delineated purpose. [How] Inline these functions, keeping the same functionality. This is not a functional change. The functions disable_i2c_hw_engine and release_engine_dce_hw were pulled into their respective callers. The most interesting part of this change is the acquire functions. dce_i2c_hw_engine_acquire_engine was pulled into dce_i2c_engine_acquire_hw, and dce_i2c_engine_acquire_hw was pulled into acquire_i2c_hw_engine. Some notes to show that this change is not functional: -Failure conditions in any function resulted in a cascade of calls that ended in a 'return NULL'. Those are replaced with a direct 'return NULL'. -The variable result is the one from dce_i2c_hw_engine_acquire_engine. The boolean result used as part of return logic was removed. -As the second half of dce_i2c_hw_engine_acquire_engine is only executed if that function is returning true and therefore exiting the do-while loop in dce_i2c_engine_acquire_hw, those lines were moved outside of the loop. Signed-off-by: David Francis <David.Francis@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2018-08-27drm/amd/display: Remove redundant i2c structsDavid Francis4-177/+28
[Why] The i2c code contains two structs that contain the same information as i2c_payload [How] Replace references to those structs with references to i2c_payload dce_i2c_transaction_request->status was written to but never read, so all references to it are removed Signed-off-by: David Francis <David.Francis@amd.com> Reviewed-by: Jordan Lazare <Jordan.Lazare@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2018-08-27drm/amd/display: Eliminate i2c hw function pointersDavid Francis2-345/+291
[Why] The function pointers of the dce_i2c_hw struct were never accessed from outside dce_i2c_hw.c and had only one version. As function pointers take up space and make debugging difficult, and they are not needed in this case, they should be removed. [How] Remove the dce_i2c_hw_funcs struct and make static all functions that were previously a part of it. Reorder the functions in dce_i2c_hw.c. Signed-off-by: David Francis <David.Francis@amd.com> Reviewed-by: Sun peng Li <Sunpeng.Li@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2018-08-27drm/amdgpu/display: add support for LVDS (v5)Alex Deucher5-0/+76
This adds support for LVDS displays. v2: add support for spread spectrum, sink detect v3: clean up enable_lvds_output v4: fix up link_detect v5: remove assert on 888 format Bug: https://bugs.freedesktop.org/show_bug.cgi?id=105880 Reviewed-by: Harry Wentland <harry.wentland@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2018-08-27drm/amd/display: Combine dce80 and dce100 i2c hw functionsDavid Francis1-197/+40
[Why] There are two versions of the hw function pointers: one for dce80 and one for all other versions. These paired functions are nearly identical. dce80 and dce100 should not require different i2c access functions. [How] Combine each pair of functions into a single function. Mostly the new functions are based on the dce100 versions as those versions are newer, support more features, and were more maintained. Signed-off-by: David Francis <David.Francis@amd.com> Reviewed-by: Sun peng Li <Sunpeng.Li@amd.com> Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2018-08-27drm/amd/display: Create new i2c resourceDavid Francis7-2/+2078
[Why] I2C code did not match dc resource model and was generally unpleasant [How] Move code into new svelte dce_i2c files, replacing various i2c objects with two structs: dce_i2c_sw and dce_i2c_hw. Fully split sw and hw code paths. Remove all redundant declarations. Use address lists to distinguish between versions. Change dce80 code to newer register access macros. Signed-off-by: David Francis <David.Francis@amd.com> Reviewed-by: Tony Cheng <Tony.Cheng@amd.com> Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2018-08-27drm/amd/display: Add dprefclk value to dce_dccgDmytro Laktyushkin2-1/+4
This allows us to avoid any vbios bugs when initializing clocks Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com> Reviewed-by: Charlene Liu <Charlene.Liu@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2018-08-27drm/amd/display: Add support for toggling DFS bypassNicholas Kazlauskas2-4/+61
[Why] If the hardware supports DFS bypass it will always be enabled after creation of the DCCG. DFS bypass should only be enabled when the current stream consists of a single embedded panel and the minimum display clock is below the DFS bypass threshold. [How] Add a function to the DCCG table that updates the DFS bypass state when setting the bandwidth. If the DFS bypass state is changed, the clock needs to be reprogrammed to reflect this before the DPREFCLK is updated for audio endpoints. The existing display clock value is used as the target display clock value when reprogramming since the resulting change will be equal or larger to the current value. These changes only specifically target dce110 but do offer a framework for support on other applicable targets. Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com> Reviewed-by: David Francis <David.Francis@amd.com> Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2018-08-27drm/amd/display: Set DFS bypass flags for dce110Nicholas Kazlauskas1-0/+3
[Why] While there is support for using and quering DFS bypass clocks the hardware is never notified to enter DFS bypass mode for dce110. [How] Add a flag that can be set when programming the display engine PLL to enable DFS bypass mode. If this flag is set then the hardware is notified to enter DFS bypass mode and the correct display engine clock frequency can be acquired. Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com> Reviewed-by: Harry Wentland <Harry.Wentland@amd.com> Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2018-08-21Revert "drm/amdgpu/display: Replace CONFIG_DRM_AMD_DC_DCN1_0 with CONFIG_X86"Leo (Sunpeng) Li6-22/+22
This reverts commit 8624c3c4dbfe24fc6740687236a2e196f5f4bfb0. We need CONFIG_DRM_AMD_DC_DCN1_0 to guard code that is using fp math. Acked-by: Alex Deucher <alexander.deucher@amd.com> Reviewed-by: Michel Dänzer <michel.daenzer@amd.com> Signed-off-by: Leo (Sunpeng) Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2018-08-21drm/amd/display: fix dentist did rangesDmytro Laktyushkin1-2/+8
Dentist did ranges were incomplete as max setting has an unusual divider step up of 66. Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com> Reviewed-by: Charlene Liu <Charlene.Liu@amd.com> Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2018-08-13drm/amd/display: Pass connector id when executing VBIOS CTMikita Lipski1-2/+2
[why] Older ASICs require both phys_id and connector_id to execute bios command table. If we are not passing the right connector_id - it can lead to a black screen. [how] Set connector_obj_id when executing vbios command table Signed-off-by: Mikita Lipski <mikita.lipski@amd.com> Reviewed-by: Hersen Wu <hersenxs.wu@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org
2018-08-06drm/amd/display: display connected to dp-1 does not light upHersen Wu1-0/+5
[why] for vega, dp set_panel_mode is handled by psp firmware. dal should not program the register again. [how] dal does not program panel mode. Signed-off-by: Hersen Wu <hersenxs.wu@amd.com> Reviewed-by: Charlene Liu <Charlene.Liu@amd.com> Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2018-08-06drm/amd/display: program display clock on cache matchDmytro Laktyushkin1-1/+3
[Why] We seem to have an issue where high enough display clock will not get set properly during S3 resume if we only call vbios once [How] Expand condition of display clock programming to happen even when cached display clock matches requested display clock Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com> Reviewed-by: Tony Cheng <Tony.Cheng@amd.com> Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2018-08-06drm/amd/display: Use calculated disp_clk_khz value for dce110Nicholas Kazlauskas1-2/+2
[Why] The calculated values for actual disp_clk_khz were ignored when notifying pplib of the new display requirements. In order to honor DFS bypass clocks from the hardware, the calculated value should be used. [How] The return value for set_dispclk is now assigned back into new_clocks and correctly carried through into dccg->clks.phyclk_khz. When notifying pplib of new display requirements dccg->clks.phyclk_khz is used instead of dce.dispclk_khz. The value of dce.dispclk_khz was never explicitly set to anything before. A 15% higher display clock value than calculated is no longer requested for dce110 since it now makes use of the calculated value. Since dce112 makes use of dce110's set_bandwidth but not its update_clocks it needs to have the value correctly carried through. Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com> Reviewed-by: Harry Wentland <Harry.Wentland@amd.com> Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com> Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2018-07-27drm/amd/display: Prevent PSR from being enabled if initialization failsAnthony Koo1-15/+23
[Why] PSR_SET command is sent to the microcontroller in order to initialize parameters needed for PSR feature, such as telling the microcontroller which pipe is driving the PSR supported panel. When this command is skipped or fails, the microcontroller may program the wrong thing if driver tries to enable PSR. [How] If PSR_SET fails, do not set psr_enable flag to indicate the feature is not yet initialized. Signed-off-by: Anthony Koo <Anthony.Koo@amd.com> Reviewed-by: Aric Cyr <Aric.Cyr@amd.com> Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2018-07-27drm/amd/display: flatten aux_engine and engineBhawanpreet Lakha2-32/+27
[Why] engine and aux_engine are unnecessary layers we want to remove this layer. [How] flatten engine and aux engine structs into one struct called aux_engine and remove all references to the engine struct. Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com> Reviewed-by: Harry Wentland <Harry.Wentland@amd.com> Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2018-07-24drm/amd/display: separate dc_debug into dc_debug_options and dc_debug dataJun Lei1-2/+2
[why] confusing as to which part of debug is informational, and which part causes behavioral change Signed-off-by: Jun Lei <Jun.Lei@amd.com> Reviewed-by: Tony Cheng <Tony.Cheng@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2018-07-24drm/amd/display: Decouple aux from i2cBhawanpreet Lakha3-1/+1054
[Why] Aux engine is created from i2caux layer. We want to remove this layer and use the engine directly. [How] Decouple aux engine from i2caux. Move aux engine related code to dce folder and use dc resource pool to manage the engine. And use the engine functions directly Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com> Reviewed-by: Harry Wentland <Harry.Wentland@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2018-07-19drm/amdgpu/display: Replace CONFIG_DRM_AMD_DC_DCN1_0 with CONFIG_X86Michel Dänzer6-22/+22
Allowing CONFIG_DRM_AMD_DC_DCN1_0 to be disabled on X86 was an opportunity for display with Raven Ridge accidentally not working. Reviewed-by: Harry Wentland <harry.wentland@amd.com> Signed-off-by: Michel Dänzer <michel.daenzer@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2018-07-16drm/amd/display: add HDR visual confirmGloria Li1-1/+1
[Why] Testing team wants a way to tell if HDR is on or not [How] Program the overscan color to visually indicate the HDR state of the top-most plane Signed-off-by: Gloria Li <geling.li@amd.com> Reviewed-by: Aric Cyr <Aric.Cyr@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2018-07-13drm/amd/display: add DalEnableHDMI20 key supportCharlene Liu1-0/+6
[why] "DalEnableHDMI20" set to 0, disallow HDMI YCbCr420 and pixel clock > 340Mhz Default is enabled. Signed-off-by: Charlene Liu <charlene.liu@amd.com> Reviewed-by: Jun Lei <Jun.Lei@amd.com> Acked-by: Harry Wentland <harry.wentland@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2018-07-13drm/amd/display: add missing mask for dcnCharlene Liu1-1/+2
Signed-off-by: Charlene Liu <charlene.liu@amd.com> Reviewed-by: Wesley Chalmers <Wesley.Chalmers@amd.com> Reviewed-by: Duke Du <Duke.Du@amd.com> Acked-by: Harry Wentland <harry.wentland@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2018-07-13drm/amd/display: drop unused register definesDmytro Laktyushkin1-6/+2
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com> Reviewed-by: Harry Wentland <Harry.Wentland@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2018-07-13drm/amd/display: Define couple extra DCN registersCharlene Liu1-0/+1
Signed-off-by: Charlene Liu <charlene.liu@amd.com> Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com> Acked-by: Harry Wentland <harry.wentland@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
generated by cgit v1.2.3 (git 2.39.1) at 2024-04-19 02:12:45 +0000