| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Pull more block updates from Jens Axboe:
"This is mainly some late lightnvm changes that came in just before the
merge window, as well as fixes that have been queued up since the
initial pull request was frozen.
This contains:
- lightnvm changes, fixing race conditions, improving memory
utilization, and improving pblk compatability (Chansol, Igor,
Marcin)
- NVMe pull request with minor fixes all over the map (via Christoph)
- remove redundant error print in sata_rcar (Geert)
- struct_size() cleanup (Jackie)
- dasd CONFIG_LBADF warning fix (Ming)
- brd cond_resched() improvement (Mikulas)"
* tag 'for-5.2/block-post-20190516' of git://git.kernel.dk/linux-block: (41 commits)
block/bio-integrity: use struct_size() in kmalloc()
nvme: validate cntlid during controller initialisation
nvme: change locking for the per-subsystem controller list
nvme: trace all async notice events
nvme: fix typos in nvme status code values
nvme-fabrics: remove unused argument
nvme-multipath: avoid crash on invalid subsystem cntlid enumeration
nvme-fc: use separate work queue to avoid warning
nvme-rdma: remove redundant reference between ib_device and tagset
nvme-pci: mark expected switch fall-through
nvme-pci: add known admin effects to augument admin effects log page
nvme-pci: init shadow doorbell after each reset
brd: add cond_resched to brd_free_pages
sata_rcar: Remove ata_host_alloc() error printing
s390/dasd: fix build warning in dasd_eckd_build_cp_raw
lightnvm: pblk: use nvm_rq_to_ppa_list()
lightnvm: pblk: simplify partial read path
lightnvm: do not remove instance under global lock
lightnvm: track inflight target creations
lightnvm: pblk: recover only written metadata
...
|
|
Pull ARM SoC platform updates from Olof Johansson:
"SoC updates, mostly refactorings and cleanups of old legacy platforms.
Major themes this release:
- Conversion of ixp4xx to a modern platform (drivers, DT, bindings)
- Moving some of the ep93xx headers around to get it closer to
multiplatform enabled.
- Cleanups of Davinci
This also contains a few patches that were queued up as fixes before
5.1 but I didn't get sent in before release"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (123 commits)
ARM: debug-ll: add default address for digicolor
ARM: u300: regulator: add MODULE_LICENSE()
ARM: ep93xx: move private headers out of mach/*
ARM: ep93xx: move pinctrl interfaces into include/linux/soc
ARM: ep93xx: keypad: stop using mach/platform.h
ARM: ep93xx: move network platform data to separate header
ARM: stm32: add AMBA support for stm32 family
MAINTAINERS: update arch/arm/mach-davinci
ARM: rockchip: add missing of_node_put in rockchip_smp_prepare_pmu
ARM: dts: Add queue manager and NPE to the IXP4xx DTSI
soc: ixp4xx: qmgr: Add DT probe code
soc: ixp4xx: qmgr: Add DT bindings for IXP4xx qmgr
soc: ixp4xx: npe: Add DT probe code
soc: ixp4xx: Add DT bindings for IXP4xx NPE
soc: ixp4xx: qmgr: Pass resources
soc: ixp4xx: Remove unused functions
soc: ixp4xx: Uninline several functions
soc: ixp4xx: npe: Pass addresses as resources
ARM: ixp4xx: Turn the QMGR into a platform device
ARM: ixp4xx: Turn the NPE into a platform device
...
|
|
ata_host_alloc() can only fail due to memory allocation failures.
Hence there is no need to print a message, as the memory allocation core
code already takes care of that.
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
ep93xx does not have a proper pinctrl driver, but does things
ad-hoc through mach/platform.h, which is also used for setting
up the boards.
To avoid using mach/*.h headers completely, let's move the interfaces
into include/linux/soc/. This is far from great, but gets the job
done here, without the need for a proper pinctrl driver.
Acked-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Ls1028a is a new introduced soc which supports ATA3.0
Signed-off-by: Peng Ma <peng.ma@nxp.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Lx2160a is a new introduced soc which supports ATA3.0
Signed-off-by: Peng Ma <peng.ma@nxp.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
When CONFIG_VMAP_STACK=y, __pa() returns incorrect physical address for
a stack virtual address. Stack DMA buffers must be avoided.
Signed-off-by: raymond pang <raymondpangxd@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Pull SCSI updates from James Bottomley:
"This is mostly update of the usual drivers: arcmsr, qla2xxx, lpfc,
hisi_sas, target/iscsi and target/core.
Additionally Christoph refactored gdth as part of the dma changes. The
major mid-layer change this time is the removal of bidi commands and
with them the whole of the osd/exofs driver and filesystem. This is a
major simplification for block and mq in particular"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (240 commits)
scsi: cxgb4i: validate tcp sequence number only if chip version <= T5
scsi: cxgb4i: get pf number from lldi->pf
scsi: core: replace GFP_ATOMIC with GFP_KERNEL in scsi_scan.c
scsi: mpt3sas: Add missing breaks in switch statements
scsi: aacraid: Fix missing break in switch statement
scsi: kill command serial number
scsi: csiostor: drop serial_number usage
scsi: mvumi: use request tag instead of serial_number
scsi: dpt_i2o: remove serial number usage
scsi: st: osst: Remove negative constant left-shifts
scsi: ufs-bsg: Allow reading descriptors
scsi: ufs: Allow reading descriptor via raw upiu
scsi: ufs-bsg: Change the calling convention for write descriptor
scsi: ufs: Remove unused device quirks
Revert "scsi: ufs: disable vccq if it's not needed by UFS device"
scsi: megaraid_sas: Remove a bunch of set but not used variables
scsi: clean obsolete return values of eh_timed_out
scsi: sd: Optimal I/O size should be a multiple of physical block size
scsi: MAINTAINERS: SCSI initiator and target tweaks
scsi: fcoe: make use of fip_mode enum complete
...
|
|
Pull block layer updates from Jens Axboe:
"Not a huge amount of changes in this round, the biggest one is that we
finally have Mings multi-page bvec support merged. Apart from that,
this pull request contains:
- Small series that avoids quiescing the queue for sysfs changes that
match what we currently have (Aleksei)
- Series of bcache fixes (via Coly)
- Series of lightnvm fixes (via Mathias)
- NVMe pull request from Christoph. Nothing major, just SPDX/license
cleanups, RR mp policy (Hannes), and little fixes (Bart,
Chaitanya).
- BFQ series (Paolo)
- Save blk-mq cpu -> hw queue mapping, removing a pointer indirection
for the fast path (Jianchao)
- fops->iopoll() added for async IO polling, this is a feature that
the upcoming io_uring interface will use (Christoph, me)
- Partition scan loop fixes (Dongli)
- mtip32xx conversion from managed resource API (Christoph)
- cdrom registration race fix (Guenter)
- MD pull from Song, two minor fixes.
- Various documentation fixes (Marcos)
- Multi-page bvec feature. This brings a lot of nice improvements
with it, like more efficient splitting, larger IOs can be supported
without growing the bvec table size, and so on. (Ming)
- Various little fixes to core and drivers"
* tag 'for-5.1/block-20190302' of git://git.kernel.dk/linux-block: (117 commits)
block: fix updating bio's front segment size
block: Replace function name in string with __func__
nbd: propagate genlmsg_reply return code
floppy: remove set but not used variable 'q'
null_blk: fix checking for REQ_FUA
block: fix NULL pointer dereference in register_disk
fs: fix guard_bio_eod to check for real EOD errors
blk-mq: use HCTX_TYPE_DEFAULT but not 0 to index blk_mq_tag_set->map
block: optimize bvec iteration in bvec_iter_advance
block: introduce mp_bvec_for_each_page() for iterating over page
block: optimize blk_bio_segment_split for single-page bvec
block: optimize __blk_segment_map_sg() for single-page bvec
block: introduce bvec_nth_page()
iomap: wire up the iopoll method
block: add bio_set_polled() helper
block: wire up block device iopoll method
fs: add an iopoll method to struct file_operations
loop: set GENHD_FL_NO_PART_SCAN after blkdev_reread_part()
loop: do not print warn message if partition scan is successful
block: bounce: make sure that bvec table is updated
...
|
|
Pull libata updates from Jens Axboe:
"Pretty quiet round: a few small fixes, comment typo, and most notably
a low level driver for the PATA Buddha controller"
* tag 'for-5.1/libata-20190301' of git://git.kernel.dk/linux-block:
ata: libahci: Only warn for AHCI_HFLAG_MULTI_MSI set when genuine custom irq handler implemented
libata: fix a typo in comment
ata: macio: Use of_node_name_eq for node name comparisons
ata: pata_samsung_cf: simplify getting .driver_data
ata: pata_platform: Add IRQF_SHARED to IRQ flags
ata: pata_of_platform: Allow to use 16-bit wide data transfer
ata: add Buddha PATA controller driver
|
|
handler implemented
For an AHCI controller with AHCI_HFLAG_MULTI_MSI flag set, we may get the
following log, regardless of whether a custom irq handler was implemented
or not:
[ 14.700238] ahci 0000:74:03.0: both AHCI_HFLAG_MULTI_MSI flag set and custom irq handler implemented
This is because we can set hpriv->irq_handler to
ahci_single_level_irq_intr() if not already set, in
ahci_init_one()->ahci_pci_save_initial_config()->ahci_save_initial_config().
Stop having this warn being misleading by adding a check for
hpriv->irq_handler != ahci_single_level_irq_intr.
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Pull in 5.0-rc6 to avoid a dumb merge conflict with fs/iomap.c.
This is needed since io_uring is now based on the block branch,
to avoid a conflict between the multi-page bvecs and the bits
of io_uring that touch the core block parts.
* tag 'v5.0-rc6': (525 commits)
Linux 5.0-rc6
x86/mm: Make set_pmd_at() paravirt aware
MAINTAINERS: Update the ocores i2c bus driver maintainer, etc
blk-mq: remove duplicated definition of blk_mq_freeze_queue
Blk-iolatency: warn on negative inflight IO counter
blk-iolatency: fix IO hang due to negative inflight counter
MAINTAINERS: unify reference to xen-devel list
x86/mm/cpa: Fix set_mce_nospec()
futex: Handle early deadlock return correctly
futex: Fix barrier comment
net: dsa: b53: Fix for failure when irq is not defined in dt
blktrace: Show requests without sector
mips: cm: reprime error cause
mips: loongson64: remove unreachable(), fix loongson_poweroff().
sit: check if IPv6 enabled before calling ip6_err_gen_icmpv6_unreach()
geneve: should not call rt6_lookup() when ipv6 was disabled
KVM: nVMX: unconditionally cancel preemption timer in free_nested (CVE-2019-7221)
KVM: x86: work around leak of uninitialized stack contents (CVE-2019-7222)
kvm: fix kvm_ioctl_create_device() reference counting (CVE-2019-6974)
signal: Better detection of synchronous signals
...
|
|
poitner -> pointer.
Signed-off-by: Chengguang Xu <cgxu519@gmx.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
We have various helpers for setting/clearing this flag, and also
a helper to check if the queue supports queueable flushes or not.
But nobody uses them anymore, kill it with fire.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Clang warns several times in the scsi subsystem (trimmed for brevity):
drivers/scsi/hpsa.c:6209:7: warning: overflow converting case value to
switch condition type (2147762695 to 18446744071562347015) [-Wswitch]
case CCISS_GETBUSTYPES:
^
drivers/scsi/hpsa.c:6208:7: warning: overflow converting case value to
switch condition type (2147762694 to 18446744071562347014) [-Wswitch]
case CCISS_GETHEARTBEAT:
^
The root cause is that the _IOC macro can generate really large numbers,
which don't fit into type 'int', which is used for the cmd parameter in
the ioctls in scsi_host_template. My research into how GCC and Clang are
handling this at a low level didn't prove fruitful. However, looking at
the rest of the kernel tree, all ioctls use an 'unsigned int' for the
cmd parameter, which will fit all of the _IOC values in the scsi/ata
subsystems.
Make that change because none of the ioctls expect a negative value for
any command, it brings the ioctls inline with the reset of the kernel,
and it removes ambiguity, which is never good when dealing with compilers.
Link: https://github.com/ClangBuiltLinux/linux/issues/85
Link: https://github.com/ClangBuiltLinux/linux/issues/154
Link: https://github.com/ClangBuiltLinux/linux/issues/157
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Acked-by: Bradley Grove <bgrove@attotech.com>
Acked-by: Don Brace <don.brace@microsemi.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Tested-by: Nick Desaulniers <ndesaulniers@google.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Convert string compares of DT node names to use of_node_name_eq helper
instead. This removes direct access to the node name pointer.
Cc: linux-ide@vger.kernel.org
Acked-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
We should get 'driver_data' from 'struct device' directly. Going via
platform_device is an unneeded step back and forth.
Acked-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
It's quite possible that multiple devices can be hooked up
to the same interrupt line with the processor. So add IRQF_SHARED
in request irq.
Acked-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
In some cases, the system bus can be configured for 16-bit mode,
in this case using read/write functions for 32-bit values
results in two cycles of 16 bits each, which is wrong.
This patch adds the devicetree flag to switch the driver to
use 16-bit mode for I/O transfers.
Acked-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Add Buddha PATA controller driver. It enables libata support for
the Buddha, Catweasel and X-Surf expansion boards on the Zorro
expansion bus.
Module removal is currently unsupported (the old IDE's buddha
driver also doesn't support it).
Tested-by: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de>
Cc: Michael Schmitz <schmitzmic@gmail.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
We've received a bugreport that using LPM with a SAMSUNG
MZ7TE512HMHP-000L1 SSD leads to system instability, we already have
a quirk for the MZ7TD256HAFV-000L9, which is also a Samsun EVO 840 /
PM851 OEM model, so it seems some of these models have a LPM issue.
This commits adds a NOLPM quirk for the model string from the new
bugeport, to avoid the reported stability issues.
Cc: stable@vger.kernel.org
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1571330
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Six fixes, all of which appear to have user visible consequences.
The DMA one is a regression fix from the merge window and of the
others, four are driver specific and one specific to the target code"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: ufs: Use explicit access size in ufshcd_dump_regs
scsi: tcmu: fix use after free
scsi: csiostor: fix NULL pointer dereference in csio_vport_set_state()
scsi: lpfc: nvmet: avoid hang / use-after-free when destroying targetport
scsi: lpfc: nvme: avoid hang / use-after-free when destroying localport
scsi: communicate max segment size to the DMA mapping code
|
|
When a host driver sets a maximum segment size we should not only propagate
that setting to the block layer, which can merge segments, but also to the
DMA mapping layer which can merge segments as well.
Fixes: 50c2e9107f ("scsi: introduce a max_segment_size host_template parameters")
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
After commit 5d32a66541c4 (PCI/ACPI: Allow ACPI to be built without
CONFIG_PCI set) dependencies on CONFIG_PCI that previously were
satisfied implicitly through dependencies on CONFIG_ACPI have to be
specified directly. PATA_ACPI is a PCI device driver but the PCI
dependency has not been explicitly called out.
Fixes: 5d32a66541c46 ("PCI/ACPI: Allow ACPI to be built without CONFIG_PCI set")
Acked-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Sinan Kaya <okaya@kernel.org>
Reviewed-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Pull block fixes from Jens Axboe:
- NVMe pull request from Christoph, with little fixes all over the map
- Loop caching fix for offset/bs change (Jaegeuk Kim)
- Block documentation tweaks (Jeff, Jon, Weiping, John)
- null_blk zoned tweak (John)
- ahch mvebu suspend/resume support. Should have gone into the merge
window, but there was some confusion on which tree had it. (Miquel)
* tag 'for-linus-20190112' of git://git.kernel.dk/linux-block: (22 commits)
ata: ahci: mvebu: request PHY suspend/resume for Armada 3700
ata: ahci: mvebu: add Armada 3700 initialization needed for S2RAM
ata: ahci: mvebu: do Armada 38x configuration only on relevant SoCs
ata: ahci: mvebu: remove stale comment
ata: libahci_platform: comply to PHY framework
loop: drop caches if offset or block_size are changed
block: fix kerneldoc comment for blk_attempt_plug_merge()
nvme: don't initlialize ctrl->cntlid twice
nvme: introduce NVME_QUIRK_IGNORE_DEV_SUBNQN
nvme: pad fake subsys NQN vid and ssvid with zeros
nvme-multipath: zero out ANA log buffer
nvme-fabrics: unset write/poll queues for discovery controllers
nvme-tcp: don't ask if controller is fabrics
nvme-tcp: remove dead code
nvme-pci: fix out of bounds access in nvme_cqe_pending
nvme-pci: rerun irq setup on IO queue init errors
nvme-pci: use the same attributes when freeing host_mem_desc_bufs.
nvme-pci: fix the wrong setting of nr_maps
block: doc: add slice_idle_us to bfq documentation
block: clarify documentation for blk_{start|finish}_plug
...
|
|
A feature has been added in the libahci driver: the possibility to set
a new flag in hpriv->flags to let the core handle PHY suspend/resume
automatically. Make use of this feature to make suspend to RAM work
with SATA drives on A3700.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
A3700 comphy initialization is done in the firmware (TF-A). Looking at
the SATA PHY initialization routine, there is a comment about "vendor
specific" registers. Two registers are mentioned. They are not
initialized there in the firmware because they are AHCI related, while
the firmware at this location does only PHY configuration. The
solution to avoid doing such initialization is relying on U-Boot.
While this work at boot time, U-Boot is definitely not going to run
during a resume after suspending to RAM.
Two possible solutions were considered:
* Fixing the firmware.
* Fixing the kernel driver.
The first solution would take ages to propagate, while the second
solution is easy to implement as the driver as been a little bit
reworked to prepare for such platform configuration. Hence, this patch
adds an Armada 3700 configuration function to set these two registers
both at boot time (in the probe) and after a suspend (in the resume
path).
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
At the beginning, only Armada 38x SoCs where supported by the
ahci_mvebu.c driver. Commit 15d3ce7b63bd ("ata: ahci_mvebu: add
support for Armada 3700 variant") introduced Armada 3700 support. As
opposed to Armada 38x SoCs, the 3700 variants do not have to configure
mbus and the regret option. This patch took care of avoiding such
configuration when not needed in the probe function, but failed to do
the same in the resume path. While doing so looks harmless by
experience, let's clean the driver logic and avoid doing this useless
configuration with Armada 3700 SoCs.
Because the logic is very similar between these two places, it has
been decided to factorize this code and put it in a "Armada 38x
configuration function". This function is part of a new
(per-compatible) platform data structure, so that the addition of such
configuration function for Armada 3700 will be eased.
Fixes: 15d3ce7b63bd ("ata: ahci_mvebu: add support for Armada 3700 variant")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
For Armada-38x (32-bit) SoCs, PM platform support has been added since:
commit 32f9494c9dfd ("ARM: mvebu: prepare pm-board.c for the
introduction of Armada 38x support")
commit 3cbd6a6ca81c ("ARM: mvebu: Add standby support")
For Armada 64-bit SoCs, like the A3700 also using this AHCI driver, PM
platform support has always existed.
There are even suspend/resume hooks in this driver since:
commit d6ecf15814888 ("ata: ahci_mvebu: add suspend/resume support")
Remove the stale comment at the end of this driver stating that all
the above does not exist yet.
Fixes: d6ecf15814888 ("ata: ahci_mvebu: add suspend/resume support")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Current implementation of the libahci does not take into account the
new PHY framework. Correct the situation by adding a call to
phy_set_mode() before phy_power_on().
PHYs should also be handled at suspend/resume time. For this, call
ahci_platform_enable/disable_phys() at suspend/resume_host() time. These
calls are guarded by a HFLAG (AHCI_HFLAG_SUSPEND_PHYS) that the user of
the libahci driver must set manually in hpriv->flags at probe time. This
is to avoid breaking users that have not been tested with this change.
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Suggested-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
We already need to zero out memory for dma_alloc_coherent(), as such
using dma_zalloc_coherent() is superflous. Phase it out.
This change was generated with the following Coccinelle SmPL patch:
@ replace_dma_zalloc_coherent @
expression dev, size, data, handle, flags;
@@
-dma_zalloc_coherent(dev, size, handle, flags)
+dma_alloc_coherent(dev, size, handle, flags)
Suggested-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>
[hch: re-ran the script on the latest tree]
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
Pull libata fix from Jens Axboe:
"This libata change missed the original libata pull request.
Just a single fix in here, fixing a missed reference drop"
* tag 'for-4.21/libata-20190102' of git://git.kernel.dk/linux-block:
ata: pata_macio: add of_node_put()
|
|
Pull libata updates from Jens Axboe:
"Here are the libata changes for this merge window. Nothing major in
here. This contains:
- GPIO descriptor conversions (Linus Walleij)
- rcar deferred probing fix (Sergei Shtylyov)"
* tag 'for-4.21/libata-20181221' of git://git.kernel.dk/linux-block:
sata_rcar: fix deferred probing
ata: palmld: Introduce state container
ata: palmld: Convert to GPIO descriptors
ata: rb532_cf: Convert to use GPIO descriptors
ata: sata_highbank: Convert to use GPIO descriptors
ata: pxa: Drop <linux/gpio.h> include
|
|
of_find_node_by_path() acquires a reference to the node
returned by it and that reference needs to be dropped by its caller.
This place doesn't do that, so fix it.
Acked-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
The driver overrides the error codes returned by platform_get_irq() to
-EINVAL, so if it returns -EPROBE_DEFER, the driver would fail the probe
permanently instead of the deferred probing. Switch to propagating the
error code upstream, still checking/overriding IRQ0 as libata regards it
as "no IRQ" (thus polling) anyway...
Fixes: 9ec36cafe43b ("of/irq: do irq resolution in platform_get_irq")
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Pull in v4.20-rc6 to resolve the conflict in NVMe, but also to get the
two corruption fixes. We're going to be overhauling the direct dispatch
path, and we need to do that on top of the changes we made for that
in mainline.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
This creates a state container struct for the Palm LifeDrive
ATA controller, and puts the ATA host and the two GPIO
descriptors into this container.
This avoids using a singleton so potentially multiple
PATA interfaces can be instantiated.
Suggested-by: Marek Vasut <marek.vasut@gmail.com>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Instead of passing GPIO numbers directly to the PalmLD
ATA driver, pass GPIO descriptors from the board file and
handle these in the driver.
Cc: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Pass a GPIO descriptor for the device instead of a hardcoded
GPIO number from the global GPIO numberspace. Use gpio
descriptors throughout.
Cut the now completely unused platform data for the CF slot.
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Waldemar Brodkorb <wbx@openadk.org>
Cc: Matt Redfearn <matt.redfearn@mips.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
This pure device tree driver is simple to convert to use
just GPIO descriptors instead of GPIO numbers. So let's
just do it.
Cc: Mark Langsdorf <mlangsdo@redhat.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
This driver does not use GPIO or anything from the GPIO header.
Drop the include.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
These devices support read zero after trim (RZAT), as they advertise to
the OS. However, the OS doesn't believe the SSDs unless they are
explicitly whitelisted.
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Juha-Matti Tilli <juha-matti.tilli@iki.fi>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Merge in -rc3 to resolve a few conflicts, but also to get a few
important fixes that have gone into mainline since the block
4.21 branch was forked off (most notably the SCSI queue issue,
which is both a conflict AND needed fix).
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
There is nothing it could synchronize against, so don't go through
the pains of acquiring the lock.
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
med_power_with_dipm still causes freezes after updating the firmware to
the latest version (DXT04L5Q).
Set model_rev to NULL and blacklist the device.
Cc: stable@vger.kernel.org
Signed-off-by: Diego Viola <diego.viola@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
This patch updates license to use SPDX-License-Identifier
instead of verbose license text.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
med_power_with_dipm causes my T450 to freeze with a SAMSUNG
MZ7TD256HAFV-000L9 SSD (firmware DXT02L5Q).
Switching the LPM to max_performance fixes this issue.
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Diego Viola <diego.viola@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
- Fix ASPM link_state teardown on removal (Lukas Wunner)
- Fix misleading _OSC ASPM message (Sinan Kaya)
- Make _OSC optional for PCI (Sinan Kaya)
- Don't initialize ASPM link state when ACPI_FADT_NO_ASPM is set
(Patrick Talbert)
- Remove x86 and arm64 node-local allocation for host bridge structures
(Punit Agrawal)
- Pay attention to device-specific _PXM node values (Jonathan Cameron)
- Support new Immediate Readiness bit (Felipe Balbi)
- Differentiate between pciehp surprise and safe removal (Lukas Wunner)
- Remove unnecessary pciehp includes (Lukas Wunner)
- Drop pciehp hotplug_slot_ops wrappers (Lukas Wunner)
- Tolerate PCIe Slot Presence Detect being hardwired to zero to
workaround broken hardware, e.g., the Wilocity switch/wireless device
(Lukas Wunner)
- Unify pciehp controller & slot structs (Lukas Wunner)
- Constify hotplug_slot_ops (Lukas Wunner)
- Drop hotplug_slot_info (Lukas Wunner)
- Embed hotplug_slot struct into users instead of allocating it
separately (Lukas Wunner)
- Initialize PCIe port service drivers directly instead of relying on
initcall ordering (Keith Busch)
- Restore PCI config state after a slot reset (Keith Busch)
- Save/restore DPC config state along with other PCI config state
(Keith Busch)
- Reference count devices during AER handling to avoid race issue with
concurrent hot removal (Keith Busch)
- If an Upstream Port reports ERR_FATAL, don't try to read the Port's
config space because it is probably unreachable (Keith Busch)
- During error handling, use slot-specific reset instead of secondary
bus reset to avoid link up/down issues on hotplug ports (Keith Busch)
- Restore previous AER/DPC handling that does not remove and
re-enumerate devices on ERR_FATAL (Keith Busch)
- Notify all drivers that may be affected by error recovery resets
(Keith Busch)
- Always generate error recovery uevents, even if a driver doesn't have
error callbacks (Keith Busch)
- Make PCIe link active reporting detection generic (Keith Busch)
- Support D3cold in PCIe hierarchies during system sleep and runtime,
including hotplug and Thunderbolt ports (Mika Westerberg)
- Handle hpmemsize/hpiosize kernel parameters uniformly, whether slots
are empty or occupied (Jon Derrick)
- Remove duplicated include from pci/pcie/err.c and unused variable
from cpqphp (YueHaibing)
- Remove driver pci_cleanup_aer_uncorrect_error_status() calls (Oza
Pawandeep)
- Uninline PCI bus accessors for better ftracing (Keith Busch)
- Remove unused AER Root Port .error_resume method (Keith Busch)
- Use kfifo in AER instead of a local version (Keith Busch)
- Use threaded IRQ in AER bottom half (Keith Busch)
- Use managed resources in AER core (Keith Busch)
- Reuse pcie_port_find_device() for AER injection (Keith Busch)
- Abstract AER interrupt handling to disconnect error injection (Keith
Busch)
- Refactor AER injection callbacks to simplify future improvments
(Keith Busch)
- Remove unused Netronome NFP32xx Device IDs (Jakub Kicinski)
- Use bitmap_zalloc() for dma_alias_mask (Andy Shevchenko)
- Add switch fall-through annotations (Gustavo A. R. Silva)
- Remove unused Switchtec quirk variable (Joshua Abraham)
- Fix pci.c kernel-doc warning (Randy Dunlap)
- Remove trivial PCI wrappers for DMA APIs (Christoph Hellwig)
- Add Intel GPU device IDs to spurious interrupt quirk (Bin Meng)
- Run Switchtec DMA aliasing quirk only on NTB endpoints to avoid
useless dmesg errors (Logan Gunthorpe)
- Update Switchtec NTB documentation (Wesley Yung)
- Remove redundant "default n" from Kconfig (Bartlomiej Zolnierkiewicz)
- Avoid panic when drivers enable MSI/MSI-X twice (Tonghao Zhang)
- Add PCI support for peer-to-peer DMA (Logan Gunthorpe)
- Add sysfs group for PCI peer-to-peer memory statistics (Logan
Gunthorpe)
- Add PCI peer-to-peer DMA scatterlist mapping interface (Logan
Gunthorpe)
- Add PCI configfs/sysfs helpers for use by peer-to-peer users (Logan
Gunthorpe)
- Add PCI peer-to-peer DMA driver writer's documentation (Logan
Gunthorpe)
- Add block layer flag to indicate driver support for PCI peer-to-peer
DMA (Logan Gunthorpe)
- Map Infiniband scatterlists for peer-to-peer DMA if they contain P2P
memory (Logan Gunthorpe)
- Register nvme-pci CMB buffer as PCI peer-to-peer memory (Logan
Gunthorpe)
- Add nvme-pci support for PCI peer-to-peer memory in requests (Logan
Gunthorpe)
- Use PCI peer-to-peer memory in nvme (Stephen Bates, Steve Wise,
Christoph Hellwig, Logan Gunthorpe)
- Cache VF config space size to optimize enumeration of many VFs
(KarimAllah Ahmed)
- Remove unnecessary <linux/pci-ats.h> include (Bjorn Helgaas)
- Fix VMD AERSID quirk Device ID matching (Jon Derrick)
- Fix Cadence PHY handling during probe (Alan Douglas)
- Signal Cadence Endpoint interrupts via AXI region 0 instead of last
region (Alan Douglas)
- Write Cadence Endpoint MSI interrupts with 32 bits of data (Alan
Douglas)
- Remove redundant controller tests for "device_type == pci" (Rob
Herring)
- Document R-Car E3 (R8A77990) bindings (Tho Vu)
- Add device tree support for R-Car r8a7744 (Biju Das)
- Drop unused mvebu PCIe capability code (Thomas Petazzoni)
- Add shared PCI bridge emulation code (Thomas Petazzoni)
- Convert mvebu to use shared PCI bridge emulation (Thomas Petazzoni)
- Add aardvark Root Port emulation (Thomas Petazzoni)
- Support 100MHz/200MHz refclocks for i.MX6 (Lucas Stach)
- Add initial power management for i.MX7 (Leonard Crestez)
- Add PME_Turn_Off support for i.MX7 (Leonard Crestez)
- Fix qcom runtime power management error handling (Bjorn Andersson)
- Update TI dra7xx unaligned access errata workaround for host mode as
well as endpoint mode (Vignesh R)
- Fix kirin section mismatch warning (Nathan Chancellor)
- Remove iproc PAXC slot check to allow VF support (Jitendra Bhivare)
- Quirk Keystone K2G to limit MRRS to 256 (Kishon Vijay Abraham I)
- Update Keystone to use MRRS quirk for host bridge instead of open
coding (Kishon Vijay Abraham I)
- Refactor Keystone link establishment (Kishon Vijay Abraham I)
- Simplify and speed up Keystone link training (Kishon Vijay Abraham I)
- Remove unused Keystone host_init argument (Kishon Vijay Abraham I)
- Merge Keystone driver files into one (Kishon Vijay Abraham I)
- Remove redundant Keystone platform_set_drvdata() (Kishon Vijay
Abraham I)
- Rename Keystone functions for uniformity (Kishon Vijay Abraham I)
- Add Keystone device control module DT binding (Kishon Vijay Abraham
I)
- Use SYSCON API to get Keystone control module device IDs (Kishon
Vijay Abraham I)
- Clean up Keystone PHY handling (Kishon Vijay Abraham I)
- Use runtime PM APIs to enable Keystone clock (Kishon Vijay Abraham I)
- Clean up Keystone config space access checks (Kishon Vijay Abraham I)
- Get Keystone outbound window count from DT (Kishon Vijay Abraham I)
- Clean up Keystone outbound window configuration (Kishon Vijay Abraham
I)
- Clean up Keystone DBI setup (Kishon Vijay Abraham I)
- Clean up Keystone ks_pcie_link_up() (Kishon Vijay Abraham I)
- Fix Keystone IRQ status checking (Kishon Vijay Abraham I)
- Add debug messages for all Keystone errors (Kishon Vijay Abraham I)
- Clean up Keystone includes and macros (Kishon Vijay Abraham I)
- Fix Mediatek unchecked return value from devm_pci_remap_iospace()
(Gustavo A. R. Silva)
- Fix Mediatek endpoint/port matching logic (Honghui Zhang)
- Change Mediatek Root Port Class Code to PCI_CLASS_BRIDGE_PCI (Honghui
Zhang)
- Remove redundant Mediatek PM domain check (Honghui Zhang)
- Convert Mediatek to pci_host_probe() (Honghui Zhang)
- Fix Mediatek MSI enablement (Honghui Zhang)
- Add Mediatek system PM support for MT2712 and MT7622 (Honghui Zhang)
- Add Mediatek loadable module support (Honghui Zhang)
- Detach VMD resources after stopping root bus to prevent orphan
resources (Jon Derrick)
- Convert pcitest build process to that used by other tools (iio, perf,
etc) (Gustavo Pimentel)
* tag 'pci-v4.20-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (140 commits)
PCI/AER: Refactor error injection fallbacks
PCI/AER: Abstract AER interrupt handling
PCI/AER: Reuse existing pcie_port_find_device() interface
PCI/AER: Use managed resource allocations
PCI: pcie: Remove redundant 'default n' from Kconfig
PCI: aardvark: Implement emulated root PCI bridge config space
PCI: mvebu: Convert to PCI emulated bridge config space
PCI: mvebu: Drop unused PCI express capability code
PCI: Introduce PCI bridge emulated config space common logic
PCI: vmd: Detach resources after stopping root bus
nvmet: Optionally use PCI P2P memory
nvmet: Introduce helper functions to allocate and free request SGLs
nvme-pci: Add support for P2P memory in requests
nvme-pci: Use PCI p2pmem subsystem to manage the CMB
IB/core: Ensure we map P2P memory correctly in rdma_rw_ctx_[init|destroy]()
block: Add PCI P2P flag for request queue
PCI/P2PDMA: Add P2P DMA driver writer's documentation
docs-rst: Add a new directory for PCI documentation
PCI/P2PDMA: Introduce configfs/sysfs enable attribute helpers
PCI/P2PDMA: Add PCI p2pmem DMA mappings to adjust the bus offset
...
|
|
Pull libata updates from Jens Axboe:
"Here are the libata changes queued up for 4.20:
- %pOFn device_node.name conversion (Rob Herring)
- Use LBAM/LBAH password defines instead of hardcoding (Linus
Walleij)
- Series adding support for the allwinner R40 AHCI controller
(Corentin Labbe)
- Disable ALPM for Ampere Computing device (Suman Tripathi)
- ahci bcrm fixes (Florian Fainelli)
- Redundant Kconfig defaults (Bartlomiej Zolnierkiewicz)
- Code cleanups (Nathan Chancellor)"
* tag 'for-4.20/libata-20181021' of git://git.kernel.dk/linux-block:
ata: remove redundant 'default n' from Kconfig
ata: ep93xx: Use proper enums for directions
ata: ahci_brcm: Allow using driver or DSL SoCs
ata: ahci_brcm: Match BCM63138 compatible strings
ata: ahci_brcm: Allow optional reset controller to be used
dt-bindings: ata: Document BCM63138 compatible string
pata_atiixp: Remove unnecessary parentheses
ata: Disable AHCI ALPM feature for Ampere Computing eMAG SATA
dt-bindings: ata: update ahci_sunxi bindings
ata: ahci_sunxi: add support for r40
dt-bindings: ata: ahci-platform: document phy-supply
ata: ahci_platform: add support for PHY controller regulator
dt-bindings: ata: ahci-platform: document ahci-supply
ata: ahci_platform: add support for AHCI controller regulator
dt-bindings: ata: ahci-platform: fix indentation of target-supply
libata: Use SMART LBAM/LBAH password defines
ata: ahci: Convert to using %pOFn instead of device_node.name
|
|
The few callers can just use dma_set_max_seg_size ()directly.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
