| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
We have if (!phy->pll) checks scattered through the driver and if
phy->pll is an error pointer, those checks will pass and bad things will
happen :(
Reviewed-by: Rob Clark <robdclark@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20190617200920.133104-1-sean@poorly.run
|
|
Fix the error paths in _dpu_kms_mmu_init() to properly
clean up the iommu domain and not call _dpu_kms_mmu_destroy() when
things are only partially setup.
Reviewed-by: Rob Clark <robdclark@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20190617200405.131843-2-sean@poorly.run
|
|
Now that mode_fixup has been removed, we can just rely on the call
from drm_helper_probe_single_connector_modes(),
Reviewed-by: Rob Clark <robdclark@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20190617200405.131843-1-sean@poorly.run
|
|
The interconnect API provides an interface for consumer drivers to
express their bandwidth needs in the SoC. This data is aggregated
and the on-chip interconnect hardware is configured to the most
appropriate power/performance profile.
Use the API to configure the interconnects and request bandwidth
between DDR and the display hardware (MDP port(s) and rotator
downscaler).
v2: update the path names to be consistent with dpu, handle the NULL
path case, updated commit msg from Georgi.
v3: split out icc setup into it's own function, and rework logic
slightly so no interconnect paths is not fatal.
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Reviewed-By: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
|
|
dpu_mdss_destroy() can get called not just from
msm_drm_uninit() but also from msm_drm_bind() in case
of any failures.
dpu_mdss_destroy() removes the icc voting by calling
icc_put. This could accidentally remove the voting
done by pm_runtime_enable.
To make the voting balanced add a minimum vote in
dpu_mdss_init() to avoid any unclocked access.
This change depends on the following patch which
introduces interconnect binding to MDSS driver:
https://patchwork.codeaurora.org/patch/708155/
Signed-off-by: Abhinav Kumar <abhinavk@codeaurora.org>
Reviewed-by: Sean Paul <sean@poorly.run>
Signed-off-by: Rob Clark <robdclark@chromium.org>
|
|
Add interconnect properties such as interconnect provider specifier
, the edge source and destination ports which are required by the
interconnect API to configure interconnect path for MDSS.
Changes in v2:
- None
Changes in v3:
- Remove common property definitions (Rob Herring)
Changes in v4:
- Use port macros and change port string names (Georgi Djakov)
Changes in v5-v7:
- None
Signed-off-by: Sravanthi Kollukuduru <skolluku@codeaurora.org>
Signed-off-by: Jayant Shekhar <jshekhar@codeaurora.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
|
|
The interconnect framework is designed to provide a
standard kernel interface to control the settings of
the interconnects on a SoC.
The interconnect API uses a consumer/provider-based model,
where the providers are the interconnect buses and the
consumers could be various drivers.
MDSS is one of the interconnect consumers which uses the
interconnect APIs to get the path between endpoints and
set its bandwidth requirement for the given interconnected
path.
Changes in v2:
- Remove error log and unnecessary check (Jordan Crouse)
Changes in v3:
- Code clean involving variable name change, removal
of extra paranthesis and variables (Matthias Kaehlcke)
Changes in v4:
- Add comments, spacings, tabs, proper port name
and icc macro (Georgi Djakov)
Changes in v5:
- Commit text and parenthesis alignment (Georgi Djakov)
Changes in v6:
- Change to new icc_set API's (Doug Anderson)
Changes in v7:
- Fixed a typo
Changes in v8:
- Handle the of_icc_get() returning NULL case. In practice
icc_set_bw() will gracefully handle the case of a NULL path,
but it's probably best for clarity to keep num_paths=0 in
this case.
Signed-off-by: Sravanthi Kollukuduru <skolluku@codeaurora.org>
Signed-off-by: Jayant Shekhar <jshekhar@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Acked-by: Georgi Djakov <georgi.djakov@linaro.org>
Reviewed-by: Sean Paul <sean@poorly.run>
|
|
Since the upstream interconnect bus framework has landed
upstream, the existing references of custom bus scaling
needs to be cleaned up.
Changes in v2:
- Fixed build error due to partial clean up
Changes in v3:
- Condense multiple lines into a single line (Sean Paul)
Changes in v4-v7:
- None
Signed-off-by: Sravanthi Kollukuduru <skolluku@codeaurora.org>
Signed-off-by: Jayant Shekhar <jshekhar@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Reviewed-by: Sean Paul <sean@poorly.run>
|
|
Clang warns:
drivers/gpu/drm/msm/dsi/phy/dsi_phy_10nm.c:80:6: warning: logical not is
only applied to the left hand side of this bitwise operator
[-Wlogical-not-parentheses]
if (!phy->cfg->quirks & V3_0_0_10NM_OLD_TIMINGS_QUIRK) {
^ ~
drivers/gpu/drm/msm/dsi/phy/dsi_phy_10nm.c:80:6: note: add parentheses
after the '!' to evaluate the bitwise operator first
if (!phy->cfg->quirks & V3_0_0_10NM_OLD_TIMINGS_QUIRK) {
^
( )
drivers/gpu/drm/msm/dsi/phy/dsi_phy_10nm.c:80:6: note: add parentheses
around left hand side expression to silence this warning
if (!phy->cfg->quirks & V3_0_0_10NM_OLD_TIMINGS_QUIRK) {
^
( )
1 warning generated.
Add parentheses around the bitwise AND so it is evaluated first then
negated.
Fixes: 3dbbf8f09e83 ("drm/msm/dsi: Add old timings quirk for 10nm phy")
Link: https://github.com/ClangBuiltLinux/linux/issues/547
Reported-by: kbuild test robot <lkp@intel.com>
Reviewed-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
Reviewed-by: Sean Paul <sean@poorly.run>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Rob Clark <robdclark@chromium.org>
|
|
The A540 is a derivative of the A530, and is found in the MSM8998 SoC.
Signed-off-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
Reviewed-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
|
|
put_iova() would attempt to dereference a NULL pointer via the
address space pointer when no IOMMU is present. Correct this by adding
the appropriate check.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
|
|
When panel probe happens after DSI probe, the DSI probe is deferred as
per current design. In the probe defer path dsi device is destroyed.
This NULL dsi device could be deferenced by the panel probe in the
mipi_dsi_attach path.
Check for NULL dsi device before accessing it.
Changes in v2:
- Add more comments on how this NULL pointer situation will be hit
Reported-by: Jeffrey Hugo <jhugo@codeaurora.org>
Tested-by: Jeffrey Hugo <jhugo@codeaurora.org>
Signed-off-by: Abhinav Kumar <abhinavk@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
|
|
Before loading the zap shader we should ensure that the reserved memory
region is big enough to hold the loaded file.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
Signed-off-by: Rob Clark <robdclark@chromium.org>
|
|
The DSI controller on the MSM8998 SoC is a 6G v2.0.0 controller which is
very similar to the v2.0.1 of SDM845.
Signed-off-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
Signed-off-by: Rob Clark <robdclark@chromium.org>
|
|
The v3.0.0 10nm phy has two different implementations between MSM8998 and
SDM845, which require different timings calculations. Unfortunately, the
hardware designers did not choose to revise the version to account for this
delta so implement a quirk instead.
Signed-off-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
Signed-off-by: Rob Clark <robdclark@chromium.org>
|
|
The MSM8998 dsi phy is 10nm v3.0.0 like SDM845, however there appear to
be minor differences such as the address space location.
Signed-off-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
Signed-off-by: Rob Clark <robdclark@chromium.org>
|
|
The DSI phy on MSM8998 is a 10nm design like SDM845, however it has some
slightly different quirks which need to be handled by drivers. Provide
a separate compatible to assist in handling the specifics.
Signed-off-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
Signed-off-by: Rob Clark <robdclark@chromium.org>
|
|
If mdp5_cfg_init fails because of an unknown major version, a null pointer
dereference occurs. This is because the caller of init expects error
pointers, but init returns NULL on error. Fix this by returning the
expected values on error.
Fixes: 2e362e1772b8 (drm/msm/mdp5: introduce mdp5_cfg module)
Signed-off-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
|
|
The GPU specific pm_suspend code assumes that the hardware is active
when the function is called, which it usually is when called as part
of pm_runtime. But during unbind, the pm_suspend functions are called
blindly resulting in a bit of a when the hardware wasn't already
active (or booted, in the case of the GMU).
Instead of calling the pm_suspend function directly, use
pm_runtime_force_suspend() which should check the correct state of
runtime and call the functions on our behalf or skip them if they are
not needed.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
|
|
In the failure path for dpu_kms_init() it is possible to get to the MMU
destroy function with uninitialized MMU structs. Check for NULL and skip
if needed.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Reviewed-by: Kristian H. Kristensen <hoegsberg@google.com>
Signed-off-by: Rob Clark <robdclark@chromium.org>
|
|
If enabling clocks fails in msm_dss_enable_clk() the code to unwind the
settings starts at 'i' which is the clock that just failed. While this
isn't harmful it does result in a number of warnings from the clock
subsystem while trying to unpreare/disable the very clock that had
just failed to prepare/enable. Skip the current failed clock during
the unwind to to avoid the extra log spew.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
|
|
Pass the index of the MMU domain in struct msm_file_private instead
of assuming gpu->id throughout the submit path. This clears the way
to change ctx->aspace to a per-instance pagetable.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
|
|
When we move to 64 bit addressing for a5xx and a6xx targets we will start
seeing pagefaults at larger addresses so format them appropriately in the
log message for easier debugging.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Reviewed-by: Kristian H. Kristensen <hoegsberg@google.com>
Signed-off-by: Rob Clark <robdclark@chromium.org>
|
|
A5XX and newer GPUs can be run in either 32 or 64 bit mode. The GPU
registers and the microcode use 64 bit virtual addressing in either
case but the upper 32 bits are ignored if the GPU is in 32 bit mode.
There is no performance disadvantage to remaining in 64 bit mode even
if we are only generating 32 bit addresses so switch over now to prepare
for using addresses above 4G on targets that support them.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
|
|
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Cc: Rob Clark <robdclark@gmail.com>
Cc: Sean Paul <sean@poorly.run>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: linux-arm-msm@vger.kernel.org
Cc: dri-devel@lists.freedesktop.org
Cc: freedreno@lists.freedesktop.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[small fixup for unused variable warning]
Signed-off-by: Rob Clark <robdclark@chromium.org>
|
|
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Cc: Rob Clark <robdclark@gmail.com>
Cc: Sean Paul <sean@poorly.run>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Jeykumar Sankaran <jsanka@codeaurora.org>
Cc: Jordan Crouse <jcrouse@codeaurora.org>
Cc: Abhinav Kumar <abhinavk@codeaurora.org>
Cc: Bruce Wang <bzwang@chromium.org>
Cc: Sravanthi Kollukuduru <skolluku@codeaurora.org>
Cc: Fritz Koenig <frkoenig@google.com>
Cc: Chandan Uddaraju <chandanu@codeaurora.org>
Cc: linux-arm-msm@vger.kernel.org
Cc: dri-devel@lists.freedesktop.org
Cc: freedreno@lists.freedesktop.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
|
|
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Cc: Rob Clark <robdclark@gmail.com>
Cc: Sean Paul <sean@poorly.run>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Jordan Crouse <jcrouse@codeaurora.org>
Cc: Mamta Shukla <mamtashukla555@gmail.com>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Cc: linux-arm-msm@vger.kernel.org
Cc: dri-devel@lists.freedesktop.org
Cc: freedreno@lists.freedesktop.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
|
|
Clang produces the following warning
drivers/gpu/drm/msm/disp/dpu1/dpu_formats.c:477:32: warning: unused
variable 'dpu_format_map_tile' [-Wunused-const-variable] static const
struct dpu_format dpu_format_map_tile[] = { ^
drivers/gpu/drm/msm/disp/dpu1/dpu_formats.c:602:32: warning: unused
variable 'dpu_format_map_p010' [-Wunused-const-variable] static const
struct dpu_format dpu_format_map_p010[] = { ^
drivers/gpu/drm/msm/disp/dpu1/dpu_formats.c:610:32: warning: unused
variable 'dpu_format_map_p010_ubwc' [-Wunused-const-variable] static
const struct dpu_format dpu_format_map_p010_ubwc[] = { ^
drivers/gpu/drm/msm/disp/dpu1/dpu_formats.c:619:32: warning: unused
variable 'dpu_format_map_tp10_ubwc' [-Wunused-const-variable] static
const struct dpu_format dpu_format_map_tp10_ubwc[] = { ^
Removing the unimplemented modifiers that cause the warning.
Cc: clang-built-linux@googlegroups.com
Link: https://github.com/ClangBuiltLinux/linux/issues/528
Signed-off-by: Nathan Huckleberry <nhuck@google.com>
Signed-off-by: Rob Clark <robdclark@chromium.org>
|
|
wait_for_completion_timeout() returns 0 on timeout and aleast 1 otherwise
so checking for < makes no sense here.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
|
|
This comment doesn't make any sense, remove it.
Suggested-by: Jordan Crouse <jcrouse@codeaurora.org>
Reviewed-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20190528182657.246714-1-sean@poorly.run
|
|
Fold it into dpu_debugfs_init.
Cc: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20190524173231.5040-2-sean@poorly.run
|
|
Instead of reaching into dev->primary for debugfs_root, use the minor
passed into debugfs_init.
This avoids creating the debug directory under /sys/kernel/debug/ and
instead creates the directory under the correct node in
/sys/kernel/debug/dri/<node>/
Reported-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20190524173231.5040-1-sean@poorly.run
|
|
This rename makes it more clear that everything initialized in the _init
function must be cleaned up in a6xx_gmu_remove. This will hopefully
dissuade people from using device managed resources (for reasons laid
out in the previous patch).
Changes in v2:
- None
Cc: Jordan Crouse <jcrouse@codeaurora.org>
Reviewed-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20190523171653.138678-6-sean@poorly.run
|
|
of_find_device_by_node() grabs a dev reference, so make sure we clear it
on error and remove.
Changes in v2:
- Added to the set (Jordan)
Cc: Jordan Crouse <jcrouse@codeaurora.org>
Reviewed-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20190523171653.138678-5-sean@poorly.run
|
|
The gmu driver is initialized and cleaned up with calls from the gpu driver. As
such, the platform device stays valid after a6xx_gmu_remove is called and the
device managed resources are not freed. In the case of gpu probe failures or
unbind, these resources will remain managed.
If the gpu bind is run again (eg: if there's a probe defer somewhere in msm),
these resources will be initialized again for the same device, creating multiple
references. In the case of irqs, this causes failures since the irqs are
not shared (nor should they be).
This patch removes all devm_* calls and manually cleans things up in
gmu_remove.
Changes in v2:
- Add iounmap and free_irq to gmu_probe error paths
Cc: Jordan Crouse <jcrouse@codeaurora.org>
Reviewed-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20190523171653.138678-4-sean@poorly.run
|
|
pdcptr and seqptr aren't necessarily valid, check them before trying to
unmap them.
Changes in v2:
- None
Cc: Jordan Crouse <jcrouse@codeaurora.org>
Reviewed-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20190523171653.138678-3-sean@poorly.run
|
|
a6xx_gmu_stop() already calls this function via shutdown or force_stop,
so it's not necessary to call it twice. Previously this would have
knocked the irq refcount out of sync, but now with the irqs_enabled flag
it's just housekeeping.
Changes in v2:
- None
Cc: Jordan Crouse <jcrouse@codeaurora.org>
Reviewed-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20190523171653.138678-2-sean@poorly.run
|
|
The driver checks for gmu->mmio as a sign that the device has been
initialized, however there are failures in probe below the mmio init.
If one of those is hit, mmio will be non-null but freed.
In that case, a6xx_gmu_probe will return an error to a6xx_gpu_init which
will in turn call a6xx_gmu_remove which checks gmu->mmio and tries to free
resources for a second time. This causes a great boom.
Fix this by adding an initialized member to gmu which is set on
successful probe and cleared on removal.
Changes in v2:
- None
Cc: Jordan Crouse <jcrouse@codeaurora.org>
Reviewed-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20190523171653.138678-1-sean@poorly.run
|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rw/ubifs
Pull UBIFS fixes from Richard Weinberger:
- build errors wrt xattrs
- mismerge which lead to a wrong Kconfig ifdef
- missing endianness conversion
* tag 'upstream-5.2-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/ubifs:
ubifs: Convert xattr inum to host order
ubifs: Use correct config name for encryption
ubifs: Fix build error without CONFIG_UBIFS_FS_XATTR
|
|
Merge yet more updates from Andrew Morton:
"A few final bits:
- large changes to vmalloc, yielding large performance benefits
- tweak the console-flush-on-panic code
- a few fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
panic: add an option to replay all the printk message in buffer
initramfs: don't free a non-existent initrd
fs/writeback.c: use rcu_barrier() to wait for inflight wb switches going into workqueue when umount
mm/compaction.c: correct zone boundary handling when isolating pages from a pageblock
mm/vmap: add DEBUG_AUGMENT_LOWEST_MATCH_CHECK macro
mm/vmap: add DEBUG_AUGMENT_PROPAGATE_CHECK macro
mm/vmalloc.c: keep track of free blocks for vmap allocation
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull more Kbuild updates from Masahiro Yamada:
- remove unneeded use of cc-option, cc-disable-warning, cc-ldoption
- exclude tracked files from .gitignore
- re-enable -Wint-in-bool-context warning
- refactor samples/Makefile
- stop building immediately if syncconfig fails
- do not sprinkle error messages when $(CC) does not exist
- move arch/alpha/defconfig to the configs subdirectory
- remove crappy header search path manipulation
- add comment lines to .config to clarify the end of menu blocks
- check uniqueness of module names (adding new warnings intentionally)
* tag 'kbuild-v5.2-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild: (24 commits)
kconfig: use 'else ifneq' for Makefile to improve readability
kbuild: check uniqueness of module names
kconfig: Terminate menu blocks with a comment in the generated config
kbuild: add LICENSES to KBUILD_ALLDIRS
kbuild: remove 'addtree' and 'flags' magic for header search paths
treewide: prefix header search paths with $(srctree)/
media: prefix header search paths with $(srctree)/
media: remove unneeded header search paths
alpha: move arch/alpha/defconfig to arch/alpha/configs/defconfig
kbuild: terminate Kconfig when $(CC) or $(LD) is missing
kbuild: turn auto.conf.cmd into a mandatory include file
.gitignore: exclude .get_maintainer.ignore and .gitattributes
kbuild: add all Clang-specific flags unconditionally
kbuild: Don't try to add '-fcatch-undefined-behavior' flag
kbuild: add some extra warning flags unconditionally
kbuild: add -Wvla flag unconditionally
arch: remove dangling asm-generic wrappers
samples: guard sub-directories with CONFIG options
kbuild: re-enable int-in-bool-context warning
MAINTAINERS: kbuild: Add pattern for scripts/*vmlinux*
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c updates from Wolfram Sang:
"Some I2C core API additions which are kind of simple but enhance error
checking for users a lot, especially by returning errno now.
There are wrappers to still support the old API but it will be removed
once all users are converted"
* 'i2c/for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: core: add device-managed version of i2c_new_dummy
i2c: core: improve return value handling of i2c_new_device and i2c_new_dummy
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4
Pull ext4 fixes from Ted Ts'o:
"Some bug fixes, and an update to the URL's for the final version of
Unicode 12.1.0"
* tag 'ext4_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
ext4: avoid panic during forced reboot due to aborted journal
ext4: fix block validity checks for journal inodes using indirect blocks
unicode: update to Unicode 12.1.0 final
unicode: add missing check for an error return from utf8lookup()
ext4: fix miscellaneous sparse warnings
ext4: unsigned int compared against zero
ext4: fix use-after-free in dx_release()
ext4: fix data corruption caused by overlapping unaligned and aligned IO
jbd2: fix potential double free
ext4: zero out the unused memory region in the extent tree block
|
|
Pull cifs fixes from Steve French:
"Minor cleanup and fixes, one for stable, four rdma (smbdirect)
related. Also adds SEEK_HOLE support"
* tag '5.2-rc-smb3-fixes' of git://git.samba.org/sfrench/cifs-2.6:
cifs: add support for SEEK_DATA and SEEK_HOLE
Fixed https://bugzilla.kernel.org/show_bug.cgi?id=202935 allow write on the same file
cifs: Allocate memory for all iovs in smb2_ioctl
cifs: Don't match port on SMBDirect transport
cifs:smbd Use the correct DMA direction when sending data
cifs:smbd When reconnecting to server, call smbd_destroy() after all MIDs have been called
cifs: use the right include for signal_pending()
smb3: trivial cleanup to smb2ops.c
cifs: cleanup smb2ops.c and normalize strings
smb3: display session id in debug data
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf tooling updates from Ingo Molnar:
"perf.data:
- Streaming compression of perf ring buffer into
PERF_RECORD_COMPRESSED user space records, resulting in ~3-5x
perf.data file size reduction on variety of tested workloads what
saves storage space on larger server systems where perf.data size
can easily reach several tens or even hundreds of GiBs, especially
when profiling with DWARF-based stacks and tracing of context
switches.
perf record:
- Improve -user-regs/intr-regs suggestions to overcome errors
perf annotate:
- Remove hist__account_cycles() from callback, speeding up branch
processing (perf record -b)
perf stat:
- Add a 'percore' event qualifier, e.g.: -e
cpu/event=0,umask=0x3,percore=1/, that sums up the event counts for
both hardware threads in a core.
We can already do this with --per-core, but it's often useful to do
this together with other metrics that are collected per hardware
thread.
I.e. now its possible to do this per-event, and have it mixed with
other events not aggregated by core.
arm64:
- Map Brahma-B53 CPUID to cortex-a53 events.
- Add Cortex-A57 and Cortex-A72 events.
csky:
- Add DWARF register mappings for libdw, allowing --call-graph=dwarf
to work on the C-SKY arch.
x86:
- Add support for recording and printing XMM registers, available,
for instance, on Icelake.
- Add uncore_upi (Intel's "Ultra Path Interconnect" events) JSON
support. UPI replaced the Intel QuickPath Interconnect (QPI) in
Xeon Skylake-SP.
Intel PT:
- Fix instructions sampling rate.
- Timestamp fixes.
- Improve exported-sql-viewer GUI, allowing, for instance, to
copy'n'paste the trees, useful for e-mailing"
* 'perf-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (73 commits)
perf stat: Support 'percore' event qualifier
perf stat: Factor out aggregate counts printing
perf tools: Add a 'percore' event qualifier
perf docs: Add description for stderr
perf intel-pt: Fix sample timestamp wrt non-taken branches
perf intel-pt: Fix improved sample timestamp
perf intel-pt: Fix instructions sampling rate
perf regs x86: Add X86 specific arch__intr_reg_mask()
perf parse-regs: Add generic support for arch__intr/user_reg_mask()
perf parse-regs: Split parse_regs
perf vendor events arm64: Add Cortex-A57 and Cortex-A72 events
perf vendor events arm64: Map Brahma-B53 CPUID to cortex-a53 events
perf vendor events arm64: Remove [[:xdigit:]] wildcard
perf jevents: Remove unused variable
perf test zstd: Fixup verbose mode output
perf tests: Implement Zstd comp/decomp integration test
perf inject: Enable COMPRESSED record decompression
perf report: Implement perf.data record decompression
perf record: Implement -z,--compression_level[=<n>] option
perf report: Add stub processing of compressed events for -D
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull clocksource updates from Ingo Molnar:
"Misc clocksource/clockevent driver updates that came in a bit late but
are ready for v5.2"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
misc: atmel_tclib: Do not probe already used TCBs
clocksource/drivers/timer-atmel-tcb: Convert tc_clksrc_suspend|resume() to static
clocksource/drivers/tcb_clksrc: Rename the file for consistency
clocksource/drivers/timer-atmel-pit: Rework Kconfig option
clocksource/drivers/tcb_clksrc: Move Kconfig option
ARM: at91: Implement clocksource selection
clocksource/drivers/tcb_clksrc: Use tcb as sched_clock
clocksource/drivers/tcb_clksrc: Stop depending on atmel_tclib
ARM: at91: move SoC specific definitions to SoC folder
clocksource/drivers/timer-milbeaut: Cleanup common register accesses
clocksource/drivers/timer-milbeaut: Add shutdown function
clocksource/drivers/timer-milbeaut: Fix to enable one-shot timer
clocksource/drivers/tegra: Rework for compensation of suspend time
clocksource/drivers/sp804: Add COMPILE_TEST to CONFIG_ARM_TIMER_SP804
clocksource/drivers/sun4i: Add a compatible for suniv
dt-bindings: timer: Add Allwinner suniv timer
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull IRQ chip updates from Ingo Molnar:
"A late irqchips update:
- New TI INTR/INTA set of drivers
- Rewrite of the stm32mp1-exti driver as a platform driver
- Update the IOMMU MSI mapping API to be RT friendly
- A number of cleanups and other low impact fixes"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (34 commits)
iommu/dma-iommu: Remove iommu_dma_map_msi_msg()
irqchip/gic-v3-mbi: Don't map the MSI page in mbi_compose_m{b, s}i_msg()
irqchip/ls-scfg-msi: Don't map the MSI page in ls_scfg_msi_compose_msg()
irqchip/gic-v3-its: Don't map the MSI page in its_irq_compose_msi_msg()
irqchip/gicv2m: Don't map the MSI page in gicv2m_compose_msi_msg()
iommu/dma-iommu: Split iommu_dma_map_msi_msg() in two parts
genirq/msi: Add a new field in msi_desc to store an IOMMU cookie
arm64: arch_k3: Enable interrupt controller drivers
irqchip/ti-sci-inta: Add msi domain support
soc: ti: Add MSI domain bus support for Interrupt Aggregator
irqchip/ti-sci-inta: Add support for Interrupt Aggregator driver
dt-bindings: irqchip: Introduce TISCI Interrupt Aggregator bindings
irqchip/ti-sci-intr: Add support for Interrupt Router driver
dt-bindings: irqchip: Introduce TISCI Interrupt router bindings
gpio: thunderx: Use the default parent apis for {request,release}_resources
genirq: Introduce irq_chip_{request,release}_resource_parent() apis
firmware: ti_sci: Add helper apis to manage resources
firmware: ti_sci: Add RM mapping table for am654
firmware: ti_sci: Add support for IRQ management
firmware: ti_sci: Add support for RM core ops
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull EFI fix from Ingo Molnar:
"Fix an EFI-fb regression that affects certain x86 systems"
* 'efi-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
fbdev/efifb: Ignore framebuffer memmap entries that lack any memory types
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull core fixes from Ingo Molnar:
"This fixes a particularly thorny munmap() bug with MPX, plus fixes a
host build environment assumption in objtool"
* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
objtool: Allow AR to be overridden with HOSTAR
x86/mpx, mm/core: Fix recursive munmap() corruption
|
