diff options
Diffstat (limited to 'drivers/gpu/drm/panel/panel-lg-lb035q02.c')
| -rw-r--r-- | drivers/gpu/drm/panel/panel-lg-lb035q02.c | 237 |
1 files changed, 237 insertions, 0 deletions
diff --git a/drivers/gpu/drm/panel/panel-lg-lb035q02.c b/drivers/gpu/drm/panel/panel-lg-lb035q02.c new file mode 100644 index 000000000000..fc82a525b071 --- /dev/null +++ b/drivers/gpu/drm/panel/panel-lg-lb035q02.c @@ -0,0 +1,237 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * LG.Philips LB035Q02 LCD Panel Driver + * + * Copyright (C) 2019 Texas Instruments Incorporated + * + * Based on the omapdrm-specific panel-lgphilips-lb035q02 driver + * + * Copyright (C) 2013 Texas Instruments Incorporated + * Author: Tomi Valkeinen <tomi.valkeinen@ti.com> + * + * Based on a driver by: Steve Sakoman <steve@sakoman.com> + */ + +#include <linux/gpio/consumer.h> +#include <linux/module.h> +#include <linux/spi/spi.h> + +#include <drm/drm_connector.h> +#include <drm/drm_modes.h> +#include <drm/drm_panel.h> + +struct lb035q02_device { + struct drm_panel panel; + + struct spi_device *spi; + struct gpio_desc *enable_gpio; +}; + +#define to_lb035q02_device(p) container_of(p, struct lb035q02_device, panel) + +static int lb035q02_write(struct lb035q02_device *lcd, u16 reg, u16 val) +{ + struct spi_message msg; + struct spi_transfer index_xfer = { + .len = 3, + .cs_change = 1, + }; + struct spi_transfer value_xfer = { + .len = 3, + }; + u8 buffer[16]; + + spi_message_init(&msg); + + /* register index */ + buffer[0] = 0x70; + buffer[1] = 0x00; + buffer[2] = reg & 0x7f; + index_xfer.tx_buf = buffer; + spi_message_add_tail(&index_xfer, &msg); + + /* register value */ + buffer[4] = 0x72; + buffer[5] = val >> 8; + buffer[6] = val; + value_xfer.tx_buf = buffer + 4; + spi_message_add_tail(&value_xfer, &msg); + + return spi_sync(lcd->spi, &msg); +} + +static int lb035q02_init(struct lb035q02_device *lcd) +{ + /* Init sequence from page 28 of the lb035q02 spec. */ + static const struct { + u16 index; + u16 value; + } init_data[] = { + { 0x01, 0x6300 }, + { 0x02, 0x0200 }, + { 0x03, 0x0177 }, + { 0x04, 0x04c7 }, + { 0x05, 0xffc0 }, + { 0x06, 0xe806 }, + { 0x0a, 0x4008 }, + { 0x0b, 0x0000 }, + { 0x0d, 0x0030 }, + { 0x0e, 0x2800 }, + { 0x0f, 0x0000 }, + { 0x16, 0x9f80 }, + { 0x17, 0x0a0f }, + { 0x1e, 0x00c1 }, + { 0x30, 0x0300 }, + { 0x31, 0x0007 }, + { 0x32, 0x0000 }, + { 0x33, 0x0000 }, + { 0x34, 0x0707 }, + { 0x35, 0x0004 }, + { 0x36, 0x0302 }, + { 0x37, 0x0202 }, + { 0x3a, 0x0a0d }, + { 0x3b, 0x0806 }, + }; + + unsigned int i; + int ret; + + for (i = 0; i < ARRAY_SIZE(init_data); ++i) { + ret = lb035q02_write(lcd, init_data[i].index, + init_data[i].value); + if (ret < 0) + return ret; + } + + return 0; +} + +static int lb035q02_disable(struct drm_panel *panel) +{ + struct lb035q02_device *lcd = to_lb035q02_device(panel); + + gpiod_set_value_cansleep(lcd->enable_gpio, 0); + + return 0; +} + +static int lb035q02_enable(struct drm_panel *panel) +{ + struct lb035q02_device *lcd = to_lb035q02_device(panel); + + gpiod_set_value_cansleep(lcd->enable_gpio, 1); + + return 0; +} + +static const struct drm_display_mode lb035q02_mode = { + .clock = 6500, + .hdisplay = 320, + .hsync_start = 320 + 20, + .hsync_end = 320 + 20 + 2, + .htotal = 320 + 20 + 2 + 68, + .vdisplay = 240, + .vsync_start = 240 + 4, + .vsync_end = 240 + 4 + 2, + .vtotal = 240 + 4 + 2 + 18, + .vrefresh = 60, + .type = DRM_MODE_TYPE_DRIVER | DRM_MODE_TYPE_PREFERRED, + .flags = DRM_MODE_FLAG_NHSYNC | DRM_MODE_FLAG_NVSYNC, + .width_mm = 70, + .height_mm = 53, +}; + +static int lb035q02_get_modes(struct drm_panel *panel) +{ + struct drm_connector *connector = panel->connector; + struct drm_display_mode *mode; + + mode = drm_mode_duplicate(panel->drm, &lb035q02_mode); + if (!mode) + return -ENOMEM; + + drm_mode_set_name(mode); + drm_mode_probed_add(connector, mode); + + connector->display_info.width_mm = lb035q02_mode.width_mm; + connector->display_info.height_mm = lb035q02_mode.height_mm; + /* + * FIXME: According to the datasheet pixel data is sampled on the + * rising edge of the clock, but the code running on the Gumstix Overo + * Palo35 indicates sampling on the negative edge. This should be + * tested on a real device. + */ + connector->display_info.bus_flags = DRM_BUS_FLAG_DE_HIGH + | DRM_BUS_FLAG_SYNC_SAMPLE_POSEDGE + | DRM_BUS_FLAG_PIXDATA_SAMPLE_NEGEDGE; + + return 1; +} + +static const struct drm_panel_funcs lb035q02_funcs = { + .disable = lb035q02_disable, + .enable = lb035q02_enable, + .get_modes = lb035q02_get_modes, +}; + +static int lb035q02_probe(struct spi_device *spi) +{ + struct lb035q02_device *lcd; + int ret; + + lcd = devm_kzalloc(&spi->dev, sizeof(*lcd), GFP_KERNEL); + if (!lcd) + return -ENOMEM; + + spi_set_drvdata(spi, lcd); + lcd->spi = spi; + + lcd->enable_gpio = devm_gpiod_get(&spi->dev, "enable", GPIOD_OUT_LOW); + if (IS_ERR(lcd->enable_gpio)) { + dev_err(&spi->dev, "failed to parse enable gpio\n"); + return PTR_ERR(lcd->enable_gpio); + } + + ret = lb035q02_init(lcd); + if (ret < 0) + return ret; + + drm_panel_init(&lcd->panel); + lcd->panel.dev = &lcd->spi->dev; + lcd->panel.funcs = &lb035q02_funcs; + + return drm_panel_add(&lcd->panel); +} + +static int lb035q02_remove(struct spi_device *spi) +{ + struct lb035q02_device *lcd = spi_get_drvdata(spi); + + drm_panel_remove(&lcd->panel); + drm_panel_disable(&lcd->panel); + + return 0; +} + +static const struct of_device_id lb035q02_of_match[] = { + { .compatible = "lgphilips,lb035q02", }, + { /* sentinel */ }, +}; + +MODULE_DEVICE_TABLE(of, lb035q02_of_match); + +static struct spi_driver lb035q02_driver = { + .probe = lb035q02_probe, + .remove = lb035q02_remove, + .driver = { + .name = "panel-lg-lb035q02", + .of_match_table = lb035q02_of_match, + }, +}; + +module_spi_driver(lb035q02_driver); + +MODULE_ALIAS("spi:lgphilips,lb035q02"); +MODULE_AUTHOR("Tomi Valkeinen <tomi.valkeinen@ti.com>"); +MODULE_DESCRIPTION("LG.Philips LB035Q02 LCD Panel driver"); +MODULE_LICENSE("GPL"); |