diff options
Diffstat (limited to 'Documentation/trace/coresight/coresight-ect.rst')
| -rw-r--r-- | Documentation/trace/coresight/coresight-ect.rst | 226 |
1 files changed, 226 insertions, 0 deletions
diff --git a/Documentation/trace/coresight/coresight-ect.rst b/Documentation/trace/coresight/coresight-ect.rst new file mode 100644 index 000000000000..a68732c5c6d6 --- /dev/null +++ b/Documentation/trace/coresight/coresight-ect.rst @@ -0,0 +1,226 @@ +.. SPDX-License-Identifier: GPL-2.0 + +============================================= +CoreSight Embedded Cross Trigger (CTI & CTM). +============================================= + + :Author: Mike Leach <mike.leach@linaro.org> + :Date: November 2019 + +Hardware Description +-------------------- + +The CoreSight Cross Trigger Interface (CTI) is a hardware device that takes +individual input and output hardware signals known as triggers to and from +devices and interconnects them via the Cross Trigger Matrix (CTM) to other +devices via numbered channels, in order to propagate events between devices. + +e.g.:: + + 0000000 in_trigs ::::::: + 0 C 0----------->: : +======>(other CTI channel IO) + 0 P 0<-----------: : v + 0 U 0 out_trigs : : Channels ***** ::::::: + 0000000 : CTI :<=========>*CTM*<====>: CTI :---+ + ####### in_trigs : : (id 0-3) ***** ::::::: v + # ETM #----------->: : ^ ####### + # #<-----------: : +---# ETR # + ####### out_trigs ::::::: ####### + +The CTI driver enables the programming of the CTI to attach triggers to +channels. When an input trigger becomes active, the attached channel will +become active. Any output trigger attached to that channel will also +become active. The active channel is propagated to other CTIs via the CTM, +activating connected output triggers there, unless filtered by the CTI +channel gate. + +It is also possible to activate a channel using system software directly +programming registers in the CTI. + +The CTIs are registered by the system to be associated with CPUs and/or other +CoreSight devices on the trace data path. When these devices are enabled the +attached CTIs will also be enabled. By default/on power up the CTIs have +no programmed trigger/channel attachments, so will not affect the system +until explicitly programmed. + +The hardware trigger connections between CTIs and devices is implementation +defined, unless the CPU/ETM combination is a v8 architecture, in which case +the connections have an architecturally defined standard layout. + +The hardware trigger signals can also be connected to non-CoreSight devices +(e.g. UART), or be propagated off chip as hardware IO lines. + +All the CTI devices are associated with a CTM. On many systems there will be a +single effective CTM (one CTM, or multiple CTMs all interconnected), but it is +possible that systems can have nets of CTIs+CTM that are not interconnected by +a CTM to each other. On these systems a CTM index is declared to associate +CTI devices that are interconnected via a given CTM. + +Sysfs files and directories +--------------------------- + +The CTI devices appear on the existing CoreSight bus alongside the other +CoreSight devices:: + + >$ ls /sys/bus/coresight/devices + cti_cpu0 cti_cpu2 cti_sys0 etm0 etm2 funnel0 replicator0 tmc_etr0 + cti_cpu1 cti_cpu3 cti_sys1 etm1 etm3 funnel1 tmc_etf0 tpiu0 + +The ``cti_cpu<N>`` named CTIs are associated with a CPU, and any ETM used by +that core. The ``cti_sys<N>`` CTIs are general system infrastructure CTIs that +can be associated with other CoreSight devices, or other system hardware +capable of generating or using trigger signals.:: + + >$ ls /sys/bus/coresight/devices/etm0/cti_cpu0 + channels ctmid enable nr_trigger_cons mgmt power powered regs + connections subsystem triggers0 triggers1 uevent + +*Key file items are:-* + * ``enable``: enables/disables the CTI. Read to determine current state. + If this shows as enabled (1), but ``powered`` shows unpowered (0), then + the enable indicates a request to enabled when the device is powered. + * ``ctmid`` : associated CTM - only relevant if system has multiple CTI+CTM + clusters that are not interconnected. + * ``nr_trigger_cons`` : total connections - triggers<N> directories. + * ``powered`` : Read to determine if the CTI is currently powered. + +*Sub-directories:-* + * ``triggers<N>``: contains list of triggers for an individual connection. + * ``channels``: Contains the channel API - CTI main programming interface. + * ``regs``: Gives access to the raw programmable CTI regs. + * ``mgmt``: the standard CoreSight management registers. + * ``connections``: Links to connected *CoreSight* devices. The number of + links can be 0 to ``nr_trigger_cons``. Actual number given by ``nr_links`` + in this directory. + + +triggers<N> directories +~~~~~~~~~~~~~~~~~~~~~~~ + +Individual trigger connection information. This describes trigger signals for +CoreSight and non-CoreSight connections. + +Each triggers directory has a set of parameters describing the triggers for +the connection. + + * ``name`` : name of connection + * ``in_signals`` : input trigger signal indexes used in this connection. + * ``in_types`` : functional types for in signals. + * ``out_signals`` : output trigger signals for this connection. + * ``out_types`` : functional types for out signals. + +e.g:: + + >$ ls ./cti_cpu0/triggers0/ + in_signals in_types name out_signals out_types + >$ cat ./cti_cpu0/triggers0/name + cpu0 + >$ cat ./cti_cpu0/triggers0/out_signals + 0-2 + >$ cat ./cti_cpu0/triggers0/out_types + pe_edbgreq pe_dbgrestart pe_ctiirq + >$ cat ./cti_cpu0/triggers0/in_signals + 0-1 + >$ cat ./cti_cpu0/triggers0/in_types + pe_dbgtrigger pe_pmuirq + +If a connection has zero signals in either the 'in' or 'out' triggers then +those parameters will be omitted. + +Channels API Directory +~~~~~~~~~~~~~~~~~~~~~~ + +This provides an easy way to attach triggers to channels, without needing +the multiple register operations that are required if manipulating the +'regs' sub-directory elements directly. + +A number of files provide this API:: + + >$ ls ./cti_sys0/channels/ + chan_clear chan_inuse chan_xtrigs_out trigin_attach + chan_free chan_pulse chan_xtrigs_reset trigin_detach + chan_gate_disable chan_set chan_xtrigs_sel trigout_attach + chan_gate_enable chan_xtrigs_in trig_filter_enable trigout_detach + trigout_filtered + +Most access to these elements take the form:: + + echo <chan> [<trigger>] > /<device_path>/<operation> + +where the optional <trigger> is only needed for trigXX_attach | detach +operations. + +e.g.:: + + >$ echo 0 1 > ./cti_sys0/channels/trigout_attach + >$ echo 0 > ./cti_sys0/channels/chan_set + +Attaches trigout(1) to channel(0), then activates channel(0) generating a +set state on cti_sys0.trigout(1) + + +*API operations* + + * ``trigin_attach, trigout_attach``: Attach a channel to a trigger signal. + * ``trigin_detach, trigout_detach``: Detach a channel from a trigger signal. + * ``chan_set``: Set the channel - the set state will be propagated around + the CTM to other connected devices. + * ``chan_clear``: Clear the channel. + * ``chan_pulse``: Set the channel for a single CoreSight clock cycle. + * ``chan_gate_enable``: Write operation sets the CTI gate to propagate + (enable) the channel to other devices. This operation takes a channel + number. CTI gate is enabled for all channels by default at power up. Read + to list the currently enabled channels on the gate. + * ``chan_gate_disable``: Write channel number to disable gate for that + channel. + * ``chan_inuse``: Show the current channels attached to any signal + * ``chan_free``: Show channels with no attached signals. + * ``chan_xtrigs_sel``: write a channel number to select a channel to view, + read to show the selected channel number. + * ``chan_xtrigs_in``: Read to show the input triggers attached to + the selected view channel. + * ``chan_xtrigs_out``:Read to show the output triggers attached to + the selected view channel. + * ``trig_filter_enable``: Defaults to enabled, disable to allow potentially + dangerous output signals to be set. + * ``trigout_filtered``: Trigger out signals that are prevented from being + set if filtering ``trig_filter_enable`` is enabled. One use is to prevent + accidental ``EDBGREQ`` signals stopping a core. + * ``chan_xtrigs_reset``: Write 1 to clear all channel / trigger programming. + Resets device hardware to default state. + + +The example below attaches input trigger index 1 to channel 2, and output +trigger index 6 to the same channel. It then examines the state of the +channel / trigger connections using the appropriate sysfs attributes. + +The settings mean that if either input trigger 1, or channel 2 go active then +trigger out 6 will go active. We then enable the CTI, and use the software +channel control to activate channel 2. We see the active channel on the +``choutstatus`` register and the active signal on the ``trigoutstatus`` +register. Finally clearing the channel removes this. + +e.g.:: + + .../cti_sys0/channels# echo 2 1 > trigin_attach + .../cti_sys0/channels# echo 2 6 > trigout_attach + .../cti_sys0/channels# cat chan_free + 0-1,3 + .../cti_sys0/channels# cat chan_inuse + 2 + .../cti_sys0/channels# echo 2 > chan_xtrigs_sel + .../cti_sys0/channels# cat chan_xtrigs_trigin + 1 + .../cti_sys0/channels# cat chan_xtrigs_trigout + 6 + .../cti_sys0/# echo 1 > enable + .../cti_sys0/channels# echo 2 > chan_set + .../cti_sys0/channels# cat ../regs/choutstatus + 0x4 + .../cti_sys0/channels# cat ../regs/trigoutstatus + 0x40 + .../cti_sys0/channels# echo 2 > chan_clear + .../cti_sys0/channels# cat ../regs/trigoutstatus + 0x0 + .../cti_sys0/channels# cat ../regs/choutstatus + 0x0 |