diff options
Diffstat (limited to 'Documentation/devicetree/bindings')
4 files changed, 94 insertions, 26 deletions
diff --git a/Documentation/devicetree/bindings/display/bridge/renesas,lvds.txt b/Documentation/devicetree/bindings/display/bridge/renesas,lvds.txt new file mode 100644 index 000000000000..4f0ab3ed3b6f --- /dev/null +++ b/Documentation/devicetree/bindings/display/bridge/renesas,lvds.txt @@ -0,0 +1,58 @@ +Renesas R-Car LVDS Encoder +========================== + +These DT bindings describe the LVDS encoder embedded in the Renesas R-Car +Gen2, R-Car Gen3 and RZ/G SoCs. + +Required properties: + +- compatible : Shall contain one of + - "renesas,r8a7743-lvds" for R8A7743 (RZ/G1M) compatible LVDS encoders + - "renesas,r8a7790-lvds" for R8A7790 (R-Car H2) compatible LVDS encoders + - "renesas,r8a7791-lvds" for R8A7791 (R-Car M2-W) compatible LVDS encoders + - "renesas,r8a7793-lvds" for R8A7793 (R-Car M2-N) compatible LVDS encoders + - "renesas,r8a7795-lvds" for R8A7795 (R-Car H3) compatible LVDS encoders + - "renesas,r8a7796-lvds" for R8A7796 (R-Car M3-W) compatible LVDS encoders + - "renesas,r8a77970-lvds" for R8A77970 (R-Car V3M) compatible LVDS encoders + - "renesas,r8a77995-lvds" for R8A77995 (R-Car D3) compatible LVDS encoders + +- reg: Base address and length for the memory-mapped registers +- clocks: A phandle + clock-specifier pair for the functional clock +- resets: A phandle + reset specifier for the module reset + +Required nodes: + +The LVDS encoder has two video ports. Their connections are modelled using the +OF graph bindings specified in Documentation/devicetree/bindings/graph.txt. + +- Video port 0 corresponds to the parallel RGB input +- Video port 1 corresponds to the LVDS output + +Each port shall have a single endpoint. + + +Example: + + lvds0: lvds@feb90000 { + compatible = "renesas,r8a7790-lvds"; + reg = <0 0xfeb90000 0 0x1c>; + clocks = <&cpg CPG_MOD 726>; + resets = <&cpg 726>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + lvds0_in: endpoint { + remote-endpoint = <&du_out_lvds0>; + }; + }; + port@1 { + reg = <1>; + lvds0_out: endpoint { + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/display/connector/dvi-connector.txt b/Documentation/devicetree/bindings/display/connector/dvi-connector.txt index fc53f7c60bc6..207e42e9eba0 100644 --- a/Documentation/devicetree/bindings/display/connector/dvi-connector.txt +++ b/Documentation/devicetree/bindings/display/connector/dvi-connector.txt @@ -10,6 +10,7 @@ Optional properties: - analog: the connector has DVI analog pins - digital: the connector has DVI digital pins - dual-link: the connector has pins for DVI dual-link +- hpd-gpios: HPD GPIO number Required nodes: - Video port for DVI input diff --git a/Documentation/devicetree/bindings/display/msm/dsi.txt b/Documentation/devicetree/bindings/display/msm/dsi.txt index a6671bd2c85a..518e9cdf0d4b 100644 --- a/Documentation/devicetree/bindings/display/msm/dsi.txt +++ b/Documentation/devicetree/bindings/display/msm/dsi.txt @@ -7,8 +7,6 @@ Required properties: - reg: Physical base address and length of the registers of controller - reg-names: The names of register regions. The following regions are required: * "dsi_ctrl" -- qcom,dsi-host-index: The ID of DSI controller hardware instance. This should - be 0 or 1, since we have 2 DSI controllers at most for now. - interrupts: The interrupt signal from the DSI block. - power-domains: Should be <&mmcc MDSS_GDSC>. - clocks: Phandles to device clocks. @@ -22,6 +20,8 @@ Required properties: * "core" For DSIv2, we need an additional clock: * "src" + For DSI6G v2.0 onwards, we need also need the clock: + * "byte_intf" - assigned-clocks: Parents of "byte" and "pixel" for the given platform. - assigned-clock-parents: The Byte clock and Pixel clock PLL outputs provided by a DSI PHY block. See [1] for details on clock bindings. @@ -88,21 +88,35 @@ Required properties: * "qcom,dsi-phy-28nm-lp" * "qcom,dsi-phy-20nm" * "qcom,dsi-phy-28nm-8960" -- reg: Physical base address and length of the registers of PLL, PHY and PHY - regulator + * "qcom,dsi-phy-14nm" + * "qcom,dsi-phy-10nm" +- reg: Physical base address and length of the registers of PLL, PHY. Some + revisions require the PHY regulator base address, whereas others require the + PHY lane base address. See below for each PHY revision. - reg-names: The names of register regions. The following regions are required: + For DSI 28nm HPM/LP/8960 PHYs and 20nm PHY: * "dsi_pll" * "dsi_phy" * "dsi_phy_regulator" + For DSI 14nm and 10nm PHYs: + * "dsi_pll" + * "dsi_phy" + * "dsi_phy_lane" - clock-cells: Must be 1. The DSI PHY block acts as a clock provider, creating 2 clocks: A byte clock (index 0), and a pixel clock (index 1). -- qcom,dsi-phy-index: The ID of DSI PHY hardware instance. This should - be 0 or 1, since we have 2 DSI PHYs at most for now. - power-domains: Should be <&mmcc MDSS_GDSC>. - clocks: Phandles to device clocks. See [1] for details on clock bindings. - clock-names: the following clocks are required: * "iface" + For 28nm HPM/LP, 28nm 8960 PHYs: +- vddio-supply: phandle to vdd-io regulator device node + For 20nm PHY: - vddio-supply: phandle to vdd-io regulator device node +- vcca-supply: phandle to vcca regulator device node + For 14nm PHY: +- vcca-supply: phandle to vcca regulator device node + For 10nm PHY: +- vdds-supply: phandle to vdds regulator device node Optional properties: - qcom,dsi-phy-regulator-ldo-mode: Boolean value indicating if the LDO mode PHY diff --git a/Documentation/devicetree/bindings/display/renesas,du.txt b/Documentation/devicetree/bindings/display/renesas,du.txt index cd48aba3bc8c..c9cd17f99702 100644 --- a/Documentation/devicetree/bindings/display/renesas,du.txt +++ b/Documentation/devicetree/bindings/display/renesas,du.txt @@ -13,13 +13,10 @@ Required Properties: - "renesas,du-r8a7794" for R8A7794 (R-Car E2) compatible DU - "renesas,du-r8a7795" for R8A7795 (R-Car H3) compatible DU - "renesas,du-r8a7796" for R8A7796 (R-Car M3-W) compatible DU + - "renesas,du-r8a77970" for R8A77970 (R-Car V3M) compatible DU + - "renesas,du-r8a77995" for R8A77995 (R-Car D3) compatible DU - - reg: A list of base address and length of each memory resource, one for - each entry in the reg-names property. - - reg-names: Name of the memory resources. The DU requires one memory - resource for the DU core (named "du") and one memory resource for each - LVDS encoder (named "lvds.x" with "x" being the LVDS controller numerical - index). + - reg: the memory-mapped I/O registers base address and length - interrupt-parent: phandle of the parent interrupt controller. - interrupts: Interrupt specifiers for the DU interrupts. @@ -29,14 +26,13 @@ Required Properties: - clock-names: Name of the clocks. This property is model-dependent. - R8A7779 uses a single functional clock. The clock doesn't need to be named. - - All other DU instances use one functional clock per channel and one - clock per LVDS encoder (if available). The functional clocks must be - named "du.x" with "x" being the channel numerical index. The LVDS clocks - must be named "lvds.x" with "x" being the LVDS encoder numerical index. - - In addition to the functional and encoder clocks, all DU versions also - support externally supplied pixel clocks. Those clocks are optional. - When supplied they must be named "dclkin.x" with "x" being the input - clock numerical index. + - All other DU instances use one functional clock per channel The + functional clocks must be named "du.x" with "x" being the channel + numerical index. + - In addition to the functional clocks, all DU versions also support + externally supplied pixel clocks. Those clocks are optional. When + supplied they must be named "dclkin.x" with "x" being the input clock + numerical index. - vsps: A list of phandle and channel index tuples to the VSPs that handle the memory interfaces for the DU channels. The phandle identifies the VSP @@ -63,15 +59,15 @@ corresponding to each DU output. R8A7794 (R-Car E2) DPAD 0 DPAD 1 - - R8A7795 (R-Car H3) DPAD 0 HDMI 0 HDMI 1 LVDS 0 R8A7796 (R-Car M3-W) DPAD 0 HDMI 0 LVDS 0 - + R8A77970 (R-Car V3M) DPAD 0 LVDS 0 - - + R8A77995 (R-Car D3) DPAD 0 LVDS 0 LVDS 1 - Example: R8A7795 (R-Car H3) ES2.0 DU du: display@feb00000 { compatible = "renesas,du-r8a7795"; - reg = <0 0xfeb00000 0 0x80000>, - <0 0xfeb90000 0 0x14>; - reg-names = "du", "lvds.0"; + reg = <0 0xfeb00000 0 0x80000>; interrupts = <GIC_SPI 256 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 268 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 269 IRQ_TYPE_LEVEL_HIGH>, @@ -79,9 +75,8 @@ Example: R8A7795 (R-Car H3) ES2.0 DU clocks = <&cpg CPG_MOD 724>, <&cpg CPG_MOD 723>, <&cpg CPG_MOD 722>, - <&cpg CPG_MOD 721>, - <&cpg CPG_MOD 727>; - clock-names = "du.0", "du.1", "du.2", "du.3", "lvds.0"; + <&cpg CPG_MOD 721>; + clock-names = "du.0", "du.1", "du.2", "du.3"; vsps = <&vspd0 0>, <&vspd1 0>, <&vspd2 0>, <&vspd0 1>; ports { |